590625
42
Zoom out
Zoom in
Vorherige Seite
1/74
Nächste Seite
42 GMC-I Messtechnik GmbH
V/Hz, Ω, Temperature, and A/Hz Measurements
5.7 Current Measurement
Notes Regarding Current Measurement
The multimeter may only be operated with installed batteries or re-
chargeable batteries. Dangerous currents are otherwise not indicated,
and the instrument may be damaged.
Set up the measuring circuit in a mechanically secure fashion, and
secure it against inadvertent breaks. Select conductor cross-sec-
tions and lay out connections such that they do not overheat.
An intermittent acoustic signal warns of current greater than 10 A.
An continuous acoustic signal warns of current greater than 16 A
.
When measuring high current values, limit them to max. 16 A for
30 seconds or 10 A for max. 5 minutes, and allow the multimeter
to cool down for 10 minutes between measurements.
For purposes of orientation, internal temperature in close prox-
imity to the jacks is displayed at the right-hand auxiliary display
in the 3 A and 10 A or 16 A ranges. If temperature rises to
above 50° C, you are warned by an intermittent acoustic sig-
nal.
The input for the current measuring range is equipped with a
fuse link. Maximum permissible voltage for the measuring cir-
cuit (= rated voltage of the fuse) is 600 V AC/DC. Use specified
fuses only! The fuse must have a breaking capacity of at least
30 kA.
If the fuse for the active current measuring range blows,
FUSEappears at the digital display, and an acoustic signal is
generated at the same time.
If a fuse should blow, eliminate the cause of overload before
placing the instrument back into service!
Fuse replacement is described in section 9.3.
Be absolutely certain that the measuring ranges are not over-
loaded beyond their allowable capacities. Limit values are in-
cluded in section 8, “Technical Data”, in the table entitled
“Measuring Functions and Measuring Ranges” in the “Over-
load Capacity” column.
*Scope of Functions, Current Measurement, Direct Connection
Scope of Functions, Current Measurement with Current Clamp Sensor
Scope of Functions, Current Measurement with Current Clamp Transformer
Function Switch Position Measuring Range
Transformation ratio SEt menu, CliP=OFF
A DC A
300 μA
3 / 30 / 300 mA
3 / 10 A (16 A)
A AC+DC TRMS
/ Hz (A AC) A
A AC / Hz (A AC) ~ A~
Hz (A AC+DC) /
A AC+DC TRMS
A
Up to 30 kHz
Hz (A AC) / A AC ~ Hz
Function Switch Position
Transformation ratio SEt menu, CliPOFF
A DC V
A AC+DC / Hz (A AC) V
Hz (A AC) / A AC+DC Hz
A AC / Hz (A AC) V~
Hz (A AC) / A AC Hz
Function Switch Position
Transformation Ratio SEt menu, CliPOFF
A DC A
A AC+DC / Hz (A AC) A
Hz (A AC) / A AC+DC A
A AC / Hz (A AC) A~
Hz (A AC) / A AC Hz
42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gossen Metrawatt METRAHIT ULTRA BT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info