590625
56
Zoom out
Zoom in
Vorherige Seite
1/74
Nächste Seite
56 GMC-I Messtechnik GmbH
Interface Operation
7 Interface Operation
The multimeters are equipped with an infrared interface for the
transmission of measurement data to a PC. Measured data are
optically transferred through the instrument housing by means of
infrared light to an interface adapter (accessory), which is at-
tached to the multimeter. The adapter’s USB interface allows for
connection to the PC with an interface cable.
Model METRAHIT ULTRA BT (M248B) optionally allows for the wire-
less data transfer via Bluetooth to a PC, smartphone or tablet PC
(based on Android operating system). Information on the smart-
phone app METRALOG is available in section 10.4.2.
Commands and parameters can be transmitted from the PC to
the multimeter in both interface operating systems as well. The
following functions can be executed:
Configure and read out measuring parameters
Select a measuring function and a measuring range
Start measurement
Read out stored measured values
7.1 Activating the Interface
The interface is automatically activated for receiving operation
(multimeter receives data from the PC) as soon as the interface is
addressed by the PC, assuming that the “1rStb” parameter has
been set to “ir on ” (see section 7.2), or the instrument is already
switched on (the first command wakes up the multimeter, but
does not yet execute any further commands).
To activate the Bluetooth interface, set parameter „COM ir “ to
COM bt “ and allocate an access key (pin) via „bt pin , see section
7.2. The Bluetooth interface is inactive when the multimeter is
switched off.
The “continuous transmission” operating mode is selected manu-
ally as described below. In this operating mode, the instrument
continuously transmits measurement data to the PC via the inter-
face adapter, which can then be displayed with the help of a ter-
minal program.
Starting Continuous Transmission Operation with Menu Functions
1nFo
... SEnd StArt
send /
IR interface: IR and an arrow pointing to the right blink during trans-
mission mode operation.
Bluetooth interface: During radio communication to the PC or
smartphone, symbol and the two cursors are flashing.
Stopping Continuous Transmission Operation with Menu Functions
1nFo
... SEnd send /
stop send
Automatic Activation and Deactivation of Transmission Mode Operation
If the sampling rate is 10 seconds or longer, the display is
switched off automatically between samples in order to prolong
battery service life. The only exception is when the multimeter is
set to continuous operation. As soon as an event occurs, the dis-
play is automatically switched back on.
MEASURE
SETUP
FUNC
ENTER
FUNC
ENTER
MEASURE
SETUP
FUNC
ENTER
FUNC
ENTER
FUNC
ENTER
56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gossen Metrawatt METRAHIT ULTRA BT wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info