590623
26
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
HOLD function
The maximum voltage value can be „stored“ on the
display when activated the button „HOLD“. The value
is recorded for approx. 30 seconds or until you press
button „HOLD“ again. The Hold-function is stopped
when again a voltage is impressed.
Note: When the measured value does not vary for
2 sec, then the maximum value is recorded.
4.3 Resistance measurements (Ω)
Before taking any resistance measurements always
check that the test object is at zero-potential.
Connect 4 mm standard test lines to the Ω- and
-socket. Adjust the device to Ω. Ohm is indicated in
the upper display line.
Note:
The arrow signalizes „out of measurement range“.
The measurement range serves for a denite
determination of impedances of 0,1 Ω – 20 MΩ.
A selection between Ω-, kΩ- and MΩ ranges occurs
automatically after applying to the impedance.
The green LED signalises resistance values that a
lower than 10 kΩ.
4.4 Current measurement (I)
Attention!
You may perform current measurement in Ex-areas
only in measuring circuits with peak values of
maximum 50 V.
You may only measure currents up to maximum 2 A.
Connect 4 mm standard test lines to the A- and
-socket.
The measurement range serves for measuring
AC/DC currents in the range of 1 mA – 2 A.
A selection between mA and A occurs automatically
after attaching the test prods.
Attention!
The moulded fuse activates with currents of more
than 2 A.
The fuse can only be changed by the manufacturer
(see section 7).
4.5 Current measurement with clamp-on ammeter
MZ 1005 (I ashes)
Attention!
Measurements with MZ 1005 are only permissible
in Ex I-areas.
Please observe the separate user instructions of the
clamp-on ammeter MZ 1005. Connect the MZ 1005
to the 7-pin universal connector.
Within the clamp-on ammeter range you can mea-
sure AC/DC currents between 0,1 and 1000 A, the
optimal measurement range is selected automati-
cally.
26
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gossen Metrawatt METRALINE EXM25 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info