Bedienungsanleitung Gossen Metrawatt METRAport 40S (Seite 5 von 28) (Englisch)

590611

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

GMC-I Messtechnik GmbH 5

1 Safety Features and Precautions

You have selected an instrument which provides you with a high level of safety.

This instrument fulfills the requirements of the applicable European and national

EC guidelines. We confirm this with the CE marking. The relevant declaration of

conformity can be obtained from GMC-I Messtechnik GmbH.

The analog/digital multimeter has been manufactured and tested in accordance

with safety regulations IEC 61010–1:2010/DIN EN 61010–1:2010/VDE 0411–

1:2011. If used for its intended purpose, safety of the operator, as well as that of

the instrument, is assured. However, safety cannot be guaranteed if the instru-

ment is used improperly or handled carelessly.

In order to maintain flawless technical safety condition, and to assure safe use, it is

imperative that you read the operating instructions thoroughly and carefully before placing

your instrument into service, and that you follow all instructions contained therein.

For your safety, as well as for protection of your multimeter, the instrument is

equipped with a miniature circuit breaker for the 10 A current measuring range.

Observe the following safety precautions

• The instrument may only be operated by persons who are capable of recog-

nizing contact hazards and implementing appropriate safety precautions.

Contact hazards exist anywhere, where voltages of greater than 33 V RMS

may occur.

• Avoid working alone when taking measurements which involve contact

hazards. Be certain that a second person is present.

• Maximum allowable voltage between terminals (3), (4), (5), (6) and ground is equal to

300 V, category II.

• The current measuring range A is equipped with a magnetic circuit breaker.

Max. allowable voltage at the meas. circuit (= miniature circuit breaker nominal

voltage) is equal to 240 V~ (AC) and 50 V (DC) against earth in the “mA”

and “A” ranges.

• The instrument may only be used for current measurement in power systems if the

electrical circuit is protected with a fuse or a circuit breaker with a rating of up to

20 A, and if nom. voltage at the system does not exceed 240 V~ (AC) or 50 V (DC).

In order to conform to the CAT requirements, an additional slow-blowing fuse link

(T16A/500V) has been fitted in series with the miniature circuit breaker which can

only be replaced by service personnel once it is tripped.

• Be prepared for the occurrence of unexpected voltages at devices under test

(e.g. defective devices). For ex., capacitors may be dangerously charged.

• Make certain that the measurement cables are in flawless condition, e.g. no

damage to insulation, no interruptions in cables or plugs etc.

• No measurements may be made with this instrument in electrical circuits

with corona discharge (high-voltage).

• Special care is required when measurements are made in HF electrical

circuits. Dangerous pulsating voltages may be present.

• Measurements under moist ambient conditions are not permitted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRAport 40S Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info