590611
9
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
GMC-I Messtechnik GmbH 9
3.3 Quick Measurements
If you wish to perform quicker measurements than those possible with the auto-
matic measuring range selection function, make sure to establish the appropriate
measuring range:
•by manual measuring range selection, i. e. by selecting the measuring range
with the best resolution, see chapter 3.2.
or
•via DATA function, see chapter 5. After the first measurement, the proper
measuring range will be automatically determined so that measurements are
performed more rapidly from the second measured value onwards.
With both functions, the established measuring range is maintained for the sub-
sequent series mode measurments.
4Display (LCD)
4.1 Display Illumination
After the instrument has been switched on, background illumination can be acti-
vated by briefly pressing the DATA/MIN/MAX and MAN/AUTO keys simultane-
ously. Illumination is switched back off by once again pressing the same keys, or
automatically after approximately 1 minute.
4.2 Digital Display
The measured value appears at the digital display with decimal point and sign (+
or -). The selected unit of measure and the type of current are displayed as well.
A minus sign is displayed to the left of the value for the measurement of zero-
frequency quantities if the positive pole of the measured quantity is applied to the
jack.
If the measuring range upper limit is exceeded for the following measured
quantities, “OL” (overload) is displayed:
V (DC), I (DC), Hz, V~ (AC), I~ (AC), 30 mF: 30999 digits
30 nF
300 F: 3099 digits
The digital display is refreshed at different rates for the individual measured
quantities (see “Display Refresh Rates” on page 24.
4.3 Analog Display
The analog display with simulated pointer and dynamic response equivalent to
that of a moving-coil mechanism, is refreshed 20 times per second. This display
is especially advantageous for the observation of measured value fluctuations,
and during balancing.
The analog display is equipped with a polarity indicator. The scale is extended 5
segments into the negative range for the measurement of zero-frequency
quantities, allowing for precise observation of measured value fluctuation around
the zero point. If the measured value exceeds the display range, a triangle is first
display at the left, and polarity at the display is reversed approximately 0.7
seconds later. If the measuring range is exceeded (> 30999 digits, in the F range
(except 30 mF) : > 3099) a triangle is displayed at the right.
Scaling at the analog display is automatic, which is quite helpful for manual
measuring range selection.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gossen Metrawatt METRAport 40S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info