Bedienungsanleitung Gossen Metrawatt METRISO C (Seite 5 von 28) (Englisch)

590650

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

GMC-I Messtechnik GmbH 5

as well as requirements in accordance with VDE 0701-0702:

Repair, modification and testing of electrical devices

The test instrument is especially well suited for:

• Systems installation

• Initial start-up

• Periodic testing

• Troubleshooting in electrical systems

All required measurements can be performed for approval reports (e.g. for

ZVEH) with the help of a set consisting of the PROFiTEST C and the

METRISO C.

Measurement values can be transmitted to a PC for printing and archiving

via the integrated IR data interface at the METRISO C. This is especially

important where product liability is concerned.

The following measurements and tests can be performed with the METRISO C:

• Insulation resistance

• Low-value resistance

• Contact current

• Voltage and frequency

• Temperature and humidity (with accessories)

The following can also be measured with a shielded measurement cable:

• Conductivity of floor coverings for electrostatic discharge

2 Safety Features and Precautions

The electronic test and measuring instrument METRISO C has been built

and tested in accordance with the following standards:

IEC 61010-1:2010, EN 61010-1:2010, VDE 0411-1:2011

IEC 61557-1, -2, -4, -10

DIN EN 61557-1:2007, -2:2007, -4:2007, -10:2001

VDE 413-1:2007, -2:2008, -4:2007, -10:2001

The safety of the user and the instrument is guaranteed provided that the

instrument is used for its intended purpose.

Read the operating instructions carefully and thoroughly before using your

instrument, and observe all instructions included therein.

The measuring and test instrument may not be used:

• If the battery compartment cover has been removed

• If external damage is apparent

• With damaged connector cables or measuring adapters

• If it no longer functions flawlessly

• After excessive stress due to transport

• While the batteries are being charged

Meanings of Symbols on the Instrument

Warning concerning a point of danger

(Attention: observe documentation!)

Protection class II device

CAT II Measuring category I I device

9 V DC charging socket for NA102 charging adapter

(

part no.

01N)

Indicates EC conformity

This device and the inserted (rechargeable) batteries may not

be disposed of with the trash.

Further information regarding the

WEEE mark can be accessed on the Internet at www.gossen-

metrawatt.com under the search term ’WEEE’

Opening of Equipment / Repair

The equipment may be opened only by authorized service personnel to

ensure the safe and correct operation of the equipment and to keep the

warranty valid.

Even original spare parts may be installed only by authorized service per-

sonnel.

In case the equipment was opened by unauthorized personnel, no war-

ranty regarding personal safety, measurement accuracy, conformity with

applicable safety measures or any consequential damage is granted by

the manufacturer.

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt METRISO C Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gossen Metrawatt METRISO C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info