Bedienungsanleitung Gossen Metrawatt PROFITEST MPRO (Seite 7 von 96) (Englisch)

590776

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

GMC-I Messtechnik GmbH 7

Any warranty claims will be forfeited when the warranty

seal has been damaged or removed.

Calibration Seal (blue seal):

See also “Recalibration” on page 96.

Data Backup

We advise you to regularly transmit your stored data to a PC in

order to prevent potential loss of data in the test instrument.

We assume no responsibility for any data loss.

We recommend the following PC software programs for data

processing and management:

•ETC

• E-Befund Manager (Austria)

•Protokollmanager

• PS3 (documentation, management, report generation and

monitoring of deadlines)

• PC.doc-WORD/EXCEL (report and list generation)

• PC.doc-ACCESS (test data management)

4 Initial Start-Up

4.1 Preparation for use

Before putting the test instrument into service and using it for the

first time, the lamination sheets must be removed from the two

sensor surfaces (finger contacts) of the test plug in order to

ensure that contact voltage is reliably detected.

4.2 Installing or Replacing the Battery Pack

Attention!

Before opening the battery compartment, disconnect the

instrument from the measuring circuit (mains) at all poles!

Note

See also section 20.2 on page 87 concerning charging

the Kompkt Akku Pack Master (Z502H) and the battery

charger Z502R.

Use Kompakt Akku Pack Master (Z502H), if possible, which is either

included in the standard equipment or available as an accessory, with

heat-sealed battery cells. Do not use any battery holders which can

be filled with individual batteries. This ensures that always a com-

plete set of batteries is replaced and all rechargeable batteries are

inserted with correct polarity in order to prevent leakage from the

batteries.

Only use commercially available battery packs if you charge them exter-

nally. The quality of these sets cannot be verified and this may, in

unfavourable cases, lead to heating and deformation (during the

charging in the device).

Dispose the battery packs or the individual rechargeable batteries

in an environmentally sound fashion when their service life has

nearly expired (approx. 80% charging capacity).

➭ Loosen the slotted screw for the battery compartment lid on

the back and remove the lid.

➭ Remove the discharged battery pack or the battery holder.

Attention!

When Using a Battery Holder:

It is imperative that you pay attention to the correct po-

larity when inserting the rechargeable batteries. If a bat-

tery has been inserted with incorrect polarity, it is not

detected by the instrument and may lead to battery leak-

age.

Individual rechargeable batteries may only be charged

externally.

➭ Slide the new battery pack/filled battery holder into the battery

compartment. The holder can only be inserted to its proper

position.

➭ Replace the lid and re-tighten the screw.

4.3 Switching the Instrument On/Off

The test instrument is switched on by pressing the ON/START key.

The menu which corresponds to the momentary selector switch

position is displayed.

The instrument can be switched off manually by simultaneously

pressing the MEM and HELP keys.

After the period of time selected in the SETUP menus has elapsed,

the instrument is switched off automatically (see “Device Set-

tings”, section 4.6.

4.4 Battery Test

If battery voltage has fallen below the permissible

lower limit, the pictograph shown at the right

appears. “Low Batt!!!” is also displayed along with a battery sym-

bol. The instrument does not function if the batteries have been

depleted excessively, and no display appears.

4.5 Charging the Battery Pack in the Tester

Attention!

Use only the charger Z502R to charge the Kompakt Akku-

Pack Master (Z502H) which has already been inserted into

the test instrument.

Make sure that the following conditions have been fulfilled be-

fore connecting the charger to the charging socket:

– Kompakt Akku-Pack Master (Z502H) has been

installed, no commercially available battery packs,

no individual rechargeable batteries, no standard

batteries

– The test instrument has been disconnected from the

measuring circuit at all poles

– The instrument must remain off during charging.

Refer to section 20.2.1 with regard to charging the battery pack

which has been inserted into the tester.

If the batteries or the battery pack have not been used or

recharged for a lengthy period of time (> 1 month), thus resulting

in excessive depletion:

Observe the charging sequence (indicated by LEDs at the char-

ger) and initiate a second charging sequence if necessary (dis-

connect the charger from the mains and from the test instrument

to this end, and then reconnect it).

Please note that the system clock stops in this case and must be

set to the correct time after the instrument has been restarted.

XY123

2012-06

D-K

15080-01-01

Consecutive number

Registration number

Date of calibration (year – month)

Deutsche Akkreditierungsstelle GmbH – calibration lab

BAT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt PROFITEST MPRO Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gossen Metrawatt PROFITEST MPRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info