Bedienungsanleitung Gossen Metrawatt PROFITEST MPRO (Seite 11 von 96) (Englisch)

590776

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

GMC-I Messtechnik GmbH 11

DB MODE – Presenting the Database in Text Mode or ID Mode

The DB MODE functions are

available as of firmware ver-

sion 01.05.00 of the test

instrument and as of ETC

version 01.31.00.

Creating Structures in TXT MODE

By default, the database in the test instrument is set to text mode,

„TXT“ is indicated in the header. You can create structural ele-

ments in the test instrument und add designations in plain text,

e. g. Customer XY, Distributor XY and Electrical Circuit XY.

Creating Structures in ID MODE

Alternatively, you can work in the ID mode. „ID“ is indicated in the

header. You can create structural elements in the test instrument

which can be labelled with ID numbers at your discretion.

Note

When data are transferred from the test instrument to the

PC or ETC, ETC always retains the presentation (TXT or

ID mode) selected in the test instrument.

When data are transferred from the PC or ETC to the test

instrument, the test instrument always retains the presen-

tation selected in ETC.

So, the respective receiver of the data always adopts the

presentation of the sender.

Note

In the test instrument, structures can either be created in

text mode or in ID mode.

In the ETC software, however, designations and ID num-

bers are always allocated.

If no texts or ID numbers have been allocated when creating the

structures in the test instrument, ETC generates the missing

entries automatically. They can be subsequently edited in the ETC

software and transferred back to the test instrument if required.

Switching Bluetooth

On/Off (

MTECH+/MXTRA/

SECULIFE IP

only)

If your PC is equipped with a Bluetooth

interface, wireless com-

munication is possible between the MTECH+, MXTRA or SECULIFE IP

and ETC user software for the transfer of data and test structures.

One-time only authentication of the respective PC with the test

instrument is a prerequisite for wireless data exchange. The func-

tion selector switch must be in the SETUP position to this end.

The correct Bluetooth

COM port must also be selected in ETC

before each data transmission sequence.

Note

Activate the Bluetooth

interface at the test instrument dur-

ing data transmission only. Interface power consumption

reduces battery service life when activated continuously.

If several test instruments are within range during authentication,

the respective name should be changed in order to rule out the

possibility of a mix-up. Blanks may not be used. The default pin

code, namely “0000”, can be changed, but this is unnecessary as

a rule. As shown in figure 3, the MAC address of the test instru-

ment is displayed in the footer as hardware information.

Render your test instrument visible prior to authentication, and

subsequently invisible for security reasons.

When Bluetooth

active (= ON), the

Bluetooth

icon

appears in the

header instead of BAT, and

an interface icon appears

instead of MEM.

A closed interface icon indicates

an active Bluetooth connection

with data transmission.

Figure 1

Figure 2

Figure 3 Figure 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt PROFITEST MPRO Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gossen Metrawatt PROFITEST MPRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info