Bedienungsanleitung Gossen Metrawatt PROFITEST MTECH plus (Seite 87 von 96) (Englisch)

590779

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

GMC-I Messtechnik GmbH 87

20 Maintenance

20.1 Firmware Revision and Calibration Information

See section 4.6.

20.2 Rechargeable Battery Operation, and Charging

Check to make sure that no leakage has occurred at the

rechargeable batteries at short, regular intervals, or after the

instrument has been in storage for a lengthy period of time.

Note

Prior to lengthy periods of rest (e. g. holiday), we recom-

mend removing the rechargeable batteries. This helps to

prevent excessive depletion or leakage of batteries,

which, under unfavourable circumstances, may cause

damage to the instrument.

If battery voltage has fallen below the allowable

lower limit, the pictograph shown at the right

appears. “Low Batt!!!” is also displayed along with a battery icon.

The instrument does not function if the batteries have been

depleted excessively, and no display appears.

Attention!

Use only the charger Z502R to charge the Kompakt Akku-

Pack Master (Z502H) which has already been inserted into

the test instrument.

Make sure that the following conditions have been fulfilled be-

fore connecting the charger to the charging socket:

– Kompakt Akku-Pack Master (Z502H) has been

installed, no commercially available battery packs, no

individual rechargeable batteries, no standard batteries

– The test instrument has been disconnected from the

measuring circuit at all poles

– The instrument must remain off during charging.

If the batteries or the battery pack (Z502H) have not been used or

recharged for a lengthy period of time (> one month), thus result-

ing in excessive depletion:

Observe the charging sequence (indicated by LEDs at the char-

ger) and initiate a second charging sequence if necessary (dis-

connect the charger from the mains and from the test instrument

to this end, and then reconnect it). Please note that the system

clock stops in this case and must be set to the correct time after

the instrument has been restarted.

20.2.1 Charging Procedure with Charger for Z502R

➭ Insert the correct mains plug for your country into the charger.

Attention!

Make sure that Kompakt Akku Pack Master (Z502H) has

been inserted, no battery holder.

For charging in the tester, only use Kompakt Akku Pack Master (Z502H),

which is either included in the standard equipment or available as an

accessory, with heat-sealed battery cells.

➭ Connect the charger to the test instrument with the jack plug,

and then to the 230 V mains with the interchangeable plug.

(The charger is suitable for mains operation only!)

Attention!

Do not switch the test instrument on during charging.

Monitoring of the charging process by the microproces-

sor might otherwise be disturbed, in which case the

charging times specified in the technical data can no lon-

ger be assured.

➭ Please refer to the operating instructions included with the

charger regarding the meanings of LED displays during the

charging process.

➭ Do not disconnect the charger from the test instrument until

the green LED (charged/ready) lights up.

20.3 Fuses

If a fuse has blown due to overload, a corresponding message

error appears at the display panel. The instrument’s voltage mea-

suring ranges are nevertheless still functional.

Replacing the Fuse

Attention!

Disconnect the device from the measuring circuit at all

poles before opening the fuse compartment lid!

➭ Loosen the slotted screws at the fuse compartment lid next to

the mains power cable with a screwdriver. The fuses are now

accessible.

➭ Replacement fuses can be accessed after opening the battery

compartment lid.

Attention!

Severe damage to the instrument may occur if incorrect

fuses are used.

Only original fuses from GMC-I Messtechnik GmbH may

be used (order no. 3-578-285-01 / SIBA 7012540.3.15

SI-EINSATZ FF 3.15/500 6.3X32).

Only original fuses assure required protection by means

of suitable blowing characteristics. Short-circuiting of

fuse terminals or the repair of fuses is prohibited, and is

life endangering!

The instrument may be damaged if fuses with incorrect

ampere ratings, breaking capacities or blowing charac-

teristics are used!

➭ Remove the defective fuse and insert a new one.

➭ Insert the fuse compartment lid after the fuse has been re-

placed and secure it by turning clockwise.

20.4 Housing

No special maintenance is required for the housing. Keep outside

surfaces clean. Use a slightly dampened cloth for cleaning. In par-

ticular for the protective rubber surfaces, we recommend a moist,

lint-free microfiber cloth. Avoid the use of cleansers, abrasives or

solvents.

Return and Environmentally Sound Disposal

The instrument is a category 9 product (monitoring and control

instrument) in accordance with ElektroG (German electrical and

electronic device law). This device is subject to the RoHS direc-

tive. Furthermore, we make reference to the fact that the current

status in this regard can be accessed on the Internet at

www.gossenmetrawatt.com by entering the search term WEEE.

In accordance with WEEE 2012/19EU and ElektroG, we

identify our electrical and electronic devices with the sym-

bol in accordance with DIN EN 50419 which is shown at

the right. Devices identified with this symbol may not be disposed

of with the trash. Please contact our service department regard-

ing the return of old devices (see address in section 22).

If the (rechargeable) batteries used in your instrument are depleted,

they must be disposed of properly in accordance with valid

national regulations.

Batteries may contain pollutants and heavy metals such as lead

(Pb), cadmium (Cd) and mercury (Hg).

The symbol to the right indicates that batteries must not

be disposed of with the trash, and must be brought to a

designated collection point.

BAT

Pb Cd Hg

Gossen Metrawatt PROFITEST MTECH plus Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info