Bedienungsanleitung Gossen Metrawatt SECUSTAR FM (Seite 16 von 160) (Englisch)

590771

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

16 GMC-I Messtechnik GmbH

Initial Start-Up – Setup

4 Initial Start-Up

4.1 Connection to the Mains (90 to 264 V, 45 to 65 Hz)

Ð Connect the test system to the mains with the mains plug as

shown in the figure. The mains plug symbol appears in the

header.

Charging the Battery Pack

Ð Initial start-up: Make sure that the battery pack is properly in-

serted and connected (see section 4.2 regarding installation of

the battery pack).

If a battery pack has been installed, it is recharged automatically

as soon as a specified threshold value is fallen short of.

The charging process is indicated by the alternating charge level

at the battery symbol. After this display appears, the test system

should remain connected to the mains for a charging time of at

least 3 hours. Initial charging time: at least 5 hours.

The duration of the charging process is extended correspondingly

in the event of mixed operation, i.e. simultaneous charging and

measuring. Practically no charging at all takes place in the event

of continuous changing from one mains connection to the next

with a dwell time of less than 4 minutes per measuring point. We

recommend charging the battery pack overnight without interrup-

tion. This applies in particular to initial start-up.

You can start fast charging any time with the key (see “Setup

Menu” in section 4.10.8). Even after the batteries have been fully

charged, the device need not be disconnected from mains power

(overcharge protection).

Note



If no battery pack has been installed, the charging symbol

appears at the display after start-up and login.

4.1.1 Automatic Recognition of Mains Connection Errors

The test system automatically recognizes mains connection errors

if the conditions in the following table have been fulfilled. The user

is informed of the type of error, and all measuring functions are

disabled in the event of danger.

Each time the system is reconnected to the mains, the following

messages appear after the first test has been started:

Ð Simultaneously touch the contact surface and tap the “OK”

button.

Ð PE connection test:

– If PE is detected, measurement is continued.

– If no PE is detected, the following message appears:

“Connect PE”, for which three options exist:

Cancel: Abort the test.

OK: Repeated attempt to detect PE.

Testing is not continued until PE has been detected.

No: Testing is continued regardless of whether or not

PE is detected.

Attention!

In the event of mains connection errors in accordance with

either of the first two cases in the following table, immedi-

ately disconnect the test system from the mains and arrange

to have the error eliminated!

Note



Voltage at the electrical system’s protective conductor (PE)

may result in distorted measurement values during testing

for the absence of voltage, or during leakage voltage mea-

surements.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt SECUSTAR FM Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info