Bedienungsanleitung Gossen Metrawatt SECUSTAR FM (Seite 98 von 160) (Englisch)

590771

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

98 GMC-I Messtechnik GmbH

Automatic Test – Administration

U/M Unit of measure for limit value, setpoint or toler-

ance

Ð Test condition in preparation

Ð MinLimitValue See following table for sample entry

Ð MaxLimitValue See following table for sample entry

Ð Setpoint Ta rg et valu e

Ð Tolerance in preparation

Examples

Note



Select a limit value which either complies with or is stricter

than the legally binding regulations.

Parameter Index Card

The parameters for the measuring function must be entered here. Various

parameters are displayed, depending upon the measuring function. Refer

to section 5, “Manually Triggered Measurements – Individual Measure-

ments” for further information.

Switch off Display / hide message

Switch on Display / hide message

Meas. type e.g. safety class type,

Type of Connection: test socket or permanent

connection

After meas.

Automatic / force test socket off

Polarity L-N or N-L

Up / Ip Test voltage in V / test current in A

fp Test frequency in Hz for I EL

Zero point

Reference point (offset) for R-PE measurement

Duration Test duration in seconds

If these messages are deactivated, attention is drawn to the fact (during

deactivation) that the device may not be switched on via the relays as of

a nominal current of greater than 10 A.

Automatic: It’s determined whether or not line voltage can remain

switched on after measurement. If so, line voltage remains switched on.

This feature can also be deactivated: “force test socket off”. In addition

to this, each measurement which requires line voltage can then be con-

figured such that the inspector is prompted by means of messages to

switch the device on and off after voltage is applied to the test socket,

and before voltage is disconnected from the test socket. This protects

the relay included in the test system.

An offset can be entered for the R-PE measurement in the automatic

test, so that 0 ? is displayed for a selected reference point which is con-

nected to the protective conductor. This is necessary in order to compen-

sate for any offset which is caused by the use of an adapter (e.g. the

AT13/32), or the offset caused by installation in the event of a perma-

nently connected DUT.

Note



Entry of a new measurement can be exited at any time by

pressing the ESC key. Entries are ignored.

Ð Add the new measurement to the catalog by tapping Save .

Test Step Abbr. MinLimit-

Value

Setpoint MaxLimit-

Value

Cross

Reference

Protective conductor meas. R PE — 0  0.3  page 45

Insulation resistance meas. R ISO 1 M 10,000 M —page 48

Leakage current I PE — 0 mA 3.5 mA page 51

Equivalent leakage current I EL — 0 mA 3.5 mA page 54

Contact current I B — 0 mA 0.5 mA page 58

Patient leakage current I PL page 61

Eq. patient leakage current I EPL page 63

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gossen Metrawatt SECUSTAR FM Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info