Bedienungsanleitung Graco Avolve (Seite 8 von 66) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

768339

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

13 14

Forward-Facing Seat:

Group 1 (9-18 kg) 

Installation using ISOcatch System and 3-point belt or using

3-point belt only

Child restraint system must be used forward-facing in the

vehicle seat.

Make sure vehicle seat belt is routed through the forward-

facing belt path marked with a bright red label.

Install this child restraint system tightly in your vehicle.

Harness straps must be at or just above the child’s shoulders.

Installing the ISOcatch system (optional)

If vehicle is equipped with ISOFIX, the vehicle lower

anchor points may be visible at the vehicle seat crease. See

your vehicle owner’s manual for exact locations, anchor

identification, and requirements for use.

 Fit the ISOcatch guides with the ISOFIX anchor points. The

ISOcatch guides can protect the surface of the vehicle

seat from being torn. They can also guide the ISOcatch

connectors.

 Press the ISOcatch adjusting button to pull out the ISOcatch

connectors.

 Rotate the ISOcatch connectors by 180 degrees until they are

pointing in the direction of the ISOcatch guides.

 Line up the ISOcatch connectors with the ISOFIX anchor

points, and then click both ISOcatch connectors into the

ISOFIX anchor points.

Make sure that both ISOcatch connectors are securely

attached to their ISOFIX anchor points. The colors of

the indicators on both ISOcatch connectors should be

completely green.

Check to make sure the child restraint is securely installed by

pulling on the both ISOcatch connectors.

To remove the ISOcatch

 Press the secondary lock button first and then the button on

the ISOcatch connectors before removing the child restraint

from the vehicle seat.

 Rotate the ISOcatch connectors by 180 degrees, then

press the ISOcatch adjusting button to fold the ISOcatch

connectors. 

Installing the child seat with 3-point

vehicle belt (mandatory)

 Recline the Child restraint system-

Place the child restraint system in recline position 3.

 Place Child restraint system Forward-Facing in the Vehicle

Seat-

Place the base flat on the vehicle seat. Push it back firmly until

the back of the child restraint system touches the vehicle seat

back.

 Route the Vehicle Seat Belt-

Thread vehicle seat belt through the forward-facing belt

path (marked with an bright red label) and buckle it. Make

sure buckle and seat belt are in line with each other. Contact

Graco if in doubt about this point. The seat belt should lay as

flat as possible and not be twisted.

 Open tab on shoulder belt lockoff as shown. Insert shoulder

seat belt into shoulder belt lockoff on side of child restraint.

 Tighten the Vehicle Seat Belt-

Press down firmly in the center of the child restraint system.

Pull on the shoulder belt to tighten.

Securing Child With 5-point Harness

 Loosen Harness Straps Lift-

Up on the harness release lever while pulling out on the

harness straps. A

Unbuckle the buckle B. Place harness straps off to the sides.

 Place Your Child in the Seat-

Place harness straps over child ’s shoulders and make sure

their back is flat against the child restraint system back.

 Buckle Harness Straps-

You will hear a “click” when buckle tongues are securely

attached. Pull up on each buckle tongue to make sure it is

securely attached.

 Be Sure the Harness Straps are at Proper Height-

Harness straps must be at or just above the child’s shoulders

A and top of child’s ears must be below top of headrest B.

 To Raise or Lower Harness Height-

Squeeze the red adjustment handle and move headrest up

or down for the proper harness height.

 Check the Buckle Position-

The correct slot is the one that is closest to your child without

being underneath them.

 To adjust , lift the lower seat pad from front of child restraint

system to expose the buckle slots.

 Turn buckle strap sideways and slide to desired slot. Make

sure buckle strap is in one of the two positions.

 Replace seat pad, making sure the buckle goes through the

same slot in the seat pad as in the plastic shell.

 Pull all the slack out from around the waist and pull up on the

harness strap. Do this both sides.

 Tighten the harness by pulling the harness adjustment strap.

When you are not able to pinch any of the harness webbing

at your child’s shoulder, the harness is tight enough.

Booster Seat

Group 2 / 3 (15-36 kg) 

Installation using ISOcatch System and

3-point belt or using 3-point belt only

Child restraint system must be forward-facing in the vehicle

seat.

Remove infant wedge when used as a booster-

A Vehicle seat belts MUST lay flat against child and MUST NOT

be twisted. Make sure vehicle seat’s shoulder belt is centered

between the child’s neck and edge of shoulder.

B Never use a vehicle lap-only seat belt across front of child.

DO NOT position vehicle shoulder belt under the child’s arm

or back.

DO NOT allow child to slouch or slide down in the booster

seat.

DO NOT position vehicle seat belt over top of armrests.

If child will not keep the vehicle seat belt properly positioned,

DO NOT use this booster seat. Use a dierent child restraint

system.

Graco Avolve Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info