Bedienungsanleitung Graco Extend (Seite 8 von 49) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

768365

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

ENEN

14 15

For a bigger baby, use the lower

harness loop 2.

 Thread the shoulder harness

straps through the head support

slot to fasten the head support

to the straps, and then pull the

adjustment webbing tight.

 Reassemble the webbing cover to

the body.

 Route the Vehicle Safety Belt

Pull out the vehicle safety belt,

rotate the child restraint forward

and thread the belt through the

two forward-facing vehicle waist

belt slots at the back of the child

restraint shell.

 Buckle the vehicle safety belt.

 Open the lock-o device and

insert the vehicle shoulder belt

through it. Close the lock-o

device onto the vehicle shoulder

belt.

Please check if child restraint is

installed tightly by moving the

child restraint back and forth at

the vehicle belt path.

(Child restraint should not move

more than 25mm/1”).

 While pressing the child restraint

rmly into the vehicle seat, pull

the vehicle shoulder belt toward

the retractor to fasten the child

restraint tightly and securely.

The child restraint cannot be

used if the vehicle safety belt

buckle (female buckle end) is too

long to anchor the child restraint

securely.

 Correctly Assembled Vehicle

Belt

Ensure vehicle shoulder belt

passes through Lock-o Device

Ensure vehicle waist belt passes

through the forward-facing

vehicle waist belt slots B

Ensure that the vehicle buckle

tongue is engaged with the

buckle correctly C

 Loosen Harness Straps

While pulling up on the webbing

adjuster, pull out the shoulder

harness straps to proper length.

 Unbuckle the buckle and then

place harness straps o to the

sides.

 Place Your Child in the Seat

Place Harness Straps Over

Child’s Shoulders And Buckle

Harness Straps

Make sure their back is at

against the car seat back.

You will hear a “click” when buckle

tongues are securely attached.

Pull up on each buckle tongue to

make sure it is securely attached.

 Tighten Harness Straps

Pull down on the adjustment

webbing to adjust the tment

around child. Ensure adjusted

properly to keep child secure,

removing any slack in the

harness.

 Be Sure the Harness Straps are

at the Proper Height

Rear-Facing: The shoulder

harness slots should be at

or slightly below the child’s

shoulder. Shoulder harness straps

that are too high or too low are

not safe.

Forward-Facing: The shoulder

harness strap slots should be

at or slightly above the child’s

shoulder. Shoulder harness straps

that are too high or too low are

not safe.

 Infant Insert

Infant insert is for child’s

protection. It must be used for

children 0-6 months. Continued

use of insert above 6 months, is

permitted rearwards facing only,

for additional support.

 Infant Body Support

Remove the head support

portion of the infant insert when

the child’s head no longer ts

comfortably.

Remove the body support

of the infant insert when the

infant’s shoulders no longer t

comfortably.

 Foam Insert

To remove, pull out the foam

insert out. Remove the foam

insert to allow more space

when the infant does not t

comfortably.

 DO NOT install this child

restraint on vehicle seats that

face sideward or rearward with

respect to the moving direction

of the vehicle.

 Do not place this child restraint in

seating positions where an active

frontal airbag is installed If your

child is still in rear-facing mode.

 DO NOT create a gap between

vehicle seat and TOP of child

restraint. A

DO NOT hang over front of

vehicle seat. B

If child will not keep the vehicle

seat belt properly positioned, DO

NOT use this child restraint, use a

dierent car seat.

 Identify Your Vehicle Safety Belt

Type

This child restraint is only suitable

for vehicle seats with 3 point

retractor safety-belt.

 Remove the webbing cover from

the body.

 At the back of the seat,

disassemble the two shoulder

harnesses from the T-shaped steel

plate.

 Pull out the shoulder harness

straps.

 Thread the shoulder harness

covers through the shoulder

harness strap slots.

 Unbuckle the buckle and then

place harness straps o to the

sides.

 Remove the fastening pieces on

sides of the seat pad from the two

slots on both sides of the body.

 Remove the fastening pieces in

front of the seat pad from the two

slots on the bottom of the body.

 Thread the adjustment webbing

and harnesses on both sides out

from the seat pad.

To remove the crotch strap cover,

rst locate the elastic on the

inside of the crotch strap cover.

Pull both the elastic and the

crotch strap cover over the buckle

to remove.

 Thread the buckle out from

seat pad slot for crotch strap to

remove the seat pad.

To clean the soft goods, please

refer to the washing label on the

child restraint.

 To assemble soft goods in reverse

steps.

 Store instruction manual in the

slot with the instruction book

icon as shown.

Replacement Parts

To purchase parts or accessories,

please contact us at the

following:

gracobaby.eu

www.gracobaby.pl

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graco Extend Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info