Bedienungsanleitung Graef MS 62 (Seite 9 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

468828

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

■ Follow the instructions regarding the

requirements for the place of instal-

lation and on the unit’s electrical con-

nection to prevent personal harm and

property damage.

■ Never touch rotating parts of the unit.

■ Never put objects or body parts in the

unit while it is running.

■ Never leave the unit unsupervised dur-

ing operation.

■ Fill the unit only up to the respec-

tive mark. If overlled, hot liquid can

emerge from the tank.

Unpacking

To unpack the unit, proceed as below:

■ Take the unit out of the carton.

■ Remove all pieces of the packing.

■ Remove any possibly extant labels from

the unit (do not remove the rating

plate).

Requirements for the installation

location

For safe and awless operation of the

unit, the place of location must meet

these prerequisites:

■ The unit must be set up on a rm, at,

level, non-slip and heat resistant base

that has sufcient load bearing capac-

ity.

■ Select the place of location so that chil-

dren cannot reach the hot surfaces of

the unit.

■ The unit is not intended for installation

in a wall or a built-in cupboard.

■ Do not set up the unit in a hot, wet or

moist environment.

■ The electric socket must be readily ac-

cessible so that the power cord can be

easily unplugged.

Electric connection

Follow these instructions about the

electrical connection for safe and aw-

less operation of the unit:

■ Before connecting the unit, compare

the connection information (voltage

and frequency) on the rating plate with

those of your electrical network. This

information must match to avoid dam-

age to the unit. If in doubt, ask your

electrician.

■ The socket must be fused with at least

a 10A circuit breaker.

■ Make sure that the power cord is not

damaged. Do not conduct it over hot

surfaces or sharp edges.

■ The connector cable must not be pulled

tight.

■ The electrical safety of the unit is only

ensured if it is connected to a prop-

erly installed protective conductor

system. Operation on a socket with-

out a protective conductor is prohib-

ited. If in doubt, have the building

installation checked by an electrician.

The manufacturer does not assume any

responsibility for damages caused by a

missing or interrupted protective con-

ductor.

Electric connection

Follow these instructions about the

electrical connection for safe and aw-

less operation of the unit:

■ Before connecting the unit, compare

the connection information (voltage

and frequency) on the rating plate with

those of your electrical network. This

information must match to avoid dam-

age to the unit. If in doubt, ask your

electrician.

■ The socket must be fused with at least

a 10A circuit breaker.

■ Make sure that the power cord is not

damaged. Do not conduct it over hot

surfaces or sharp edges.

■ The connector cable must not be pulled

tight.

■ The electrical safety of the unit is only

ensured if it is connected to a prop-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graef MS 62 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info