Bedienungsanleitung Gram KS2400 (Seite 36 von 47) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Schwedisch, Norwegisch, Finnisch)

482112

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Start the refrigerator by plugging it into a

wall socket.

On connection, an alarm is activated to

indicate that the internal cabinet tempera-

ture is too high and that there has been a

power failure. Read “Alarm” to see how the

alarm can be switched off.

Illustration shows the electronic control

panel in the mid-upper part of the cabinet.

The electronically controlled refrigerator is

factory-set to run at an optimum tempera-

ture. The cabinet temperature can be

seen/changed with key °C.

When you press the key and hold it in, the

actual cabinet temperature setting will

appear almost instantaneously. This setting

is displayed for about 3 seconds. Holding

down the key will enable you to change the

temperature setting (see below).

Press °C and hold it in. The actual setting

will be displayed almost instantaneously;

the figures will light up one after the other

on the scale. When the end of the scale is

reached, all figures will go out for a

moment before they start lighting up again.

Release the key when the figure under the

required temperature lights up. The

refrigerator will now run on the new setting.

Press °C as under “Changing the tempera-

ture”, but release the key the moment all

figures go out. This cuts off the refrigerating

function and the cabinet interior can be cle-

aned. It remains possible to read the cabi-

net temperature for about 2 hours, after

which this function is automatically swi-

tched off.

After cleaning, start the refrigerator again

by setting a temperature (see “Changing

the temperature”).

The alarm is activated in the event of

power failure, or if the cabinet temperature

remains 6°C higher than the setting for

more than 2 hours. The alarm will continue

even though the temperature returns to

normal, just to make sure you know that

something has been wrong.

Alarm on starting

Your new GRAM model will not have been

started since it was tested in the factory

and therefore when you start it in your

kitchen the electronics “think” that there

has been a power failure. The alarm is

therefore activated.

Alarm deactivation

Press °C and hold it in. The temperature

setting will be displayed almost instantane-

ously. Release the key as soon as the set-

ting appears, to cancel the alarm.

When the figure 9 on the display lights up,

the temperature in the refrigerator is +9°C

or higher than can be shown on the di-

splay.

When the figure 2 flashes - and only this

figure - the temperature in the refrigerator

is lower than can be shown on the display.

When the two outermost figures on each

side of the display flash alternately with the

four middle figures, it means that there is a

defect in the temperature sensor.

Alarm: The figures light up one after

Alarm

Changing the

temperature

Cutting off for

cleaning/defrosting

Electronic control

Signals

Type 76-004-1260 09/09/04 10:48 Side 36

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gram KS2400 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info