Bedienungsanleitung Grandstream GXP-1100 (Seite 31 von 35) (Englisch)

470674

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Grandstream Networks, Inc. GXP1100/1105 User Manual Page 30 of 34

Firmware version: 1.0.1.110 Last Updated: 01/2012

Check SIP User ID for

Incoming INVITE

Check the SIP User ID in Request URI. If they don’t match, the call will be rejected.

Preferred Vocoder

GXP1100/1105 supports up to 7 different Vocoder types including G.711(a/µ) (also

known as PCMU/PCMA), G.723.1, G.729A/B, G.726-32, iLBC, G.722 (wide-band).

Configure Vocoders in a preference list that is included with the same preference

order in SDP message. Enter the first Vocoder in this list by choosing the

appropriate option in “Choice 1”. Similarly, enter the last Vocoder in this list by

choosing the appropriate option in “Choice 8”.

SRTP Mode

Enable SRTP mode based on selection. Default is “No”.

Symmetric RTP

Selects whether or not symmetric RTP is supported.

Silence Suppression

This controls the silence suppression/VAD feature of the audio codec G.723 and

G.729. If set to “Yes”, when silence is detected, a small quantity of VAD packets

(instead of audio packets) will be sent during the period of no talking. If set to “No”,

this feature is disabled.

Voice Frames per TX

This field contains the number of voice frames to be transmitted in a single Ethernet

packet (be advised the IS limit is based on the maximum size of Ethernet packet is

1500 byte (or 120kbps)).

When setting this value, be aware of the requested packet time (ptime, used in SDP

message) is a result of configuring this parameter. This parameter is associated

with the first codec in the above codec Preference List or the actual used payload

type negotiated between the 2 conversation parties at run time. E.g., if the first

codec is configured as G.723 and the “Voice Frames per TX” is set to 2, then the

“ptime” value in the SDP message of an INVITE request will be 60ms because each

G.723 voice frame contains 30ms of audio. Similarly, if this field is set to 2 and the

first codec is G.729 or G.711 or G.726, then the “ptime” value in the SDP message

of an INVITE request will be 20ms.

If the configured voice frames per TX exceeds the maximum allowed value, the IP

phone will use and save the maximum allowed value for the corresponding first

codec choice. The maximum value for PCM is 10 (x10ms) frames; for G.726, it is 20

(x10ms) frames; for G.723, it is 32 (x30ms) frames; for G.729/G.728, 64 (x10ms)

and 64 (x2.5ms) frames respectively.

Please be careful when editing these parameters. Adjusting these parameters will

also change the dynamic jitter buffer. The GXP1100/1105 has a patent dynamic

jitter buffer handling algorithm. The jitter buffer range is 20 ~ 200 ms.

We recommend using the default settings provided. We do not recommend

adjusting these parameters if you are an average user. Incorrect settings will affect

the voice quality.

No Key Entry Timeout

Default is 4 seconds.

Use # as Dial Key

This parameter allows users to configure the “#” key as the “Send” (or “Dial”) key. If

set to “Yes”, the “#” key will immediately send the call. In this case, this key is

essentially equivalent to the “(Re)Dial” key. If set to “No”, the “#” key is included as

part of the dial string.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grandstream GXP-1100 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info