Bedienungsanleitung Grandstream GXP-1200 (Seite 17 von 44) (Englisch)

470664

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Grandstream Networks, Inc. GXP User Manual Page 17 of 44

Firmware 1.2.5.3 Last Updated: 03/2011

MAKING PHONE CALLS

Handset, Speakerphone and Headset Mode

The GXP series phones allow you make phone calls via handset, speakerphone, or headset mode. During

the active calls the user can switch between the handset and the speaker by pressing the speaker key. For

headsets to operate, the user must plug the headset to an RJ22 or 2.5mm port on the phone, which allows

the user to pick-up, speak, or hang-up calls.

Multiple SIP Accounts and Lines

GXP can support up to six independent SIP accounts depending on the product model. Each account is

capable of independent SIP server, user and NAT settings. Each of the line buttons is “virtually” mapped to

an individual SIP account. The name of each account is conveniently printed next to its corresponding

button. In off-hook state, select an idle line and the name of the account (as configured in the web interface)

is displayed on the LCD and a dial tone is heard.

For example: Configure ACCOUNT 1 and ACCOUNT 2 with Account Name as “VoIP 1”, “VoIP 2”,

respectively and ensure that they are active and registered. When LINE1 is pressed, you will hear a dial

tone and see “VoIP 1” on the LCD display; when LINE2 is pressed, you will hear a dial tone and see “VoIP 2”

on the LCD display.

To make a call, select the line you wish to use. The corresponding LINE LED will light up in green. User can

switch lines before dialing any number by pressing the same LINE button one or more times. If you continue

to press a LINE button, the selected account will circulate among the registered accounts.

For example: when LINE1 is pressed, the LCD displays “VoIP 1”; If LINE1 is pressed twice, the LCD

displays “VoIP 2” and the subsequent call will be made through SIP account 2.

Incoming calls to a specific account will attempt to use its corresponding LINE if it is not in use. When the

“virtually” mapped line is in use, the GXP will flash the next available LINE (from left to right or from top to

bottom for Multi Purpose Keys) in red. A line is ACTIVE when it is in use and the corresponding LED is red.

Completing Calls

There are six ways to complete a call:

1. D

IAL: To make a phone call.

• Take Handset/SPEAKER/Headset off-hook

or press an available LINE key (activates speakerphone)

or press the NEW CALL soft-key.

• The line will have a dial tone and the primary line (LINE1) LED is red.

If you wish, select another LINE key (alternative SIP account).

• Enter the phone number

• Press the SEND key

or press the “DIAL” soft-key.

2. R

EDIAL: To redial the last dialed phone number.

When redialing, the phone will use the same SIP account as was used for the last call. Thus, when

the third SIP account was used for the last call/call attempt, the phone will use the third account to

redial.

• Take Handset/SPEAKER/Headset off-hook or

press an available LINE key (activates speakerphone), the corresponding LED will be red.

• Press the SEND button

or press the REDIAL soft-key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grandstream GXP-1200 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Grandstream GXP-1200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info