Bedienungsanleitung Grandstream GXV-3000 (Seite 41 von 54) (Englisch)

67329

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Grandstream Networks, Inc. GXV-3000 User Manual Page 39 of 54

Firmware 1.1.3.50 Updated: 04/2009

Alternatively, download and install a free TFTP or HTTP server and perform firmware upgrades. Free

Windows version TFTP server is available: http://support.solarwinds.net/updates/New-customerFree.cfm

Or http://tftpd32.jounin.net/

Instructions to Configure a Local TFTP Server:

1. Unzip the file and put all of them under the root directory of the TFTP server.

2. The PC running the TFTP server software and the GXV-3000 should be in the

same LAN segment.

3. Make sure the firmware files are in the correct root folder of TFTP server. If using

Solarwinds free TFTP server, make sure changing the TFTP server's default set-

ting from "Receive Only" to "Transmit Only" for the firmware upgrade. Then start

the server by running the TFTP server software.

4. In the phone’s web configuration page, configure the Firmware Server Path to the

IP address of the PC running the TFTP software.

5. Update the change and reboot the phone.

You can also download the free HTTP server from

HTUhttp://httpd.apache.org/UTH or use Microsoft IIS web

server embedded in some version of Windows OS.

NOTE: When GXV-3000 phone boots up, it will send TFTP or HTTP request to download configuration

file “cfg000b82xxxxxx”, where “000b82xxxxxx” is the MAC address of the GXV-3000 phone. This file is

for initial provisioning purpose only. For normal TFTP or HTTP firmware upgrades, the following error

messages in a TFTP or HTTP server log can be ignored: “TFTP Error from [IP ADRESS] requesting

cfg000b82023dd4 : File does not exist. Configuration File Download”.

CONFIGURATION FILE DOWNLOAD

The GXV-3000 can be configured via Web Interface as well as via Configuration File through TFTP or

HTTP. “Config Server Path” is the TFTP or HTTP server path for the configuration file. It needs to be set

to a valid URL, either in FQDN or IP address format.

The configuration parameter is associated with each particular field in the web configuration page. A pa-

rameter consists of a capital letter P and 2 or 3 (could be extended to 4 in the future) digit numeric num-

bers. i.e., P2 is associated with “Admin Password” in the ADVANCED SETTINGS page. For a detailed

parameter list, please refer to the corresponding configuration template of the firmware.

Once the GXV-3000 boots up (or re-booted), it will request a binary configuration file named

“cfgxxxxxxxxxxxx”, where “xxxxxxxxxxxx” is the MAC address of the device, i.e., “cfg000b820102ab”.

The configuration file name should be in lower cases.

NOTE: For earlier hardware versions (prior to V1.1), a manual power cycle

is required if the LCD is pale

or changes to the color white after firmware upgrade or configuration file downloading. For hardware ver-

sions after V1.1, the GXV-3000 automatically reboots itself after such process.

If the firmware crashes for an unknown reason during upgrade and the phone cannot boot up, please

press “#” and “*” keys simultaneously then power up the phone. This will force the phone to load the

stored boot file so that user can flash the phone again with good firmware files.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grandstream GXV-3000 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info