Bedienungsanleitung Grandstream GXW400x Series (Seite 48 von 60) (Englisch)

505348

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

FIRMWARE VERSION 1.0.8.4 GXW40XX USER MANUAL Page 48 of 60

Disable Visual MWI

Visual message indicator is a special on-hook caller ID type message that enables and

disables the message waiting light on certain phones. GXW40XX has this feature

enabled by default. However, certain phones (rare) that do not support it may mistakenly

treat this CID signal as an incoming call. A configuration option is needed to turn on MWI

in this case.

Visual MWI Type

This is the type of signal sent to the analog phone to make it turn the lamp ON upon

receiving a Voice mail. Check the phone’s manual to find out what signal is supported,

FSK (default) or Neon.

Note: This is only supported in model GXW4024 ver 4.A or newer.

Ring Timeout

Incoming call will stop ringing when not picked up given a specific period of time.

Hunting Group Ring

Timeout

Default is 20 seconds. If call is not answered within this designated time period, the call

will be forwarded to the next member of a Hunt Group.

Hunting Group Type

Linear and Circular. Linear style will sort the call to the lowest-numbered available line,

this is also called “serial hunting”. Circular style will distribute the calls "round-robin". If a

call is assigned to line 1, the next call goes to 2 and the next to 3. The succession

throughout each of the lines continues even if one of the previous lines becomes

available. When the end of the hunt group is reached, the hunting starts over at the first

line. Lines are skipped if they are still busy on a previous call. These two hunting styles

can be configured from the Profile_x page.

Delayed Call Forward

Wait Timeout

Default value is 20 seconds. In case this feature activated using * codes (*92 code), the

call will be forwarded after this preconfigured amount of time.

No Key Entry Timeout

Default is 4 seconds. Call will be completed within this time interval if no additional key

entry occurs.

Early Dial

Default is No. Use only if proxy supports 484 response. This parameter controls

whether the phone will send an early INVITE each time a key is pressed when a user

dials a number. If set to “Yes”, an INVITE is sent using the dial-number collected thus

far; Otherwise, no INVITE is sent until the “(Re-)Dial” button is pressed or after about 5

seconds have elapsed if the user forgets to press the “Re-Dial” button. The “Yes” option

should be used ONLY if there is a SIP proxy configured and the proxy server supports

484 Incomplete Address response. Otherwise, the call will likely be rejected by the proxy

(with a 404 Not Found error).

This feature is NOT designed to work with and should NOT be enabled for direct IP-to-IP

calling.

Dial Plan Prefix

Sets the prefix added to each dialed number.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grandstream GXW400x Series Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info