Bedienungsanleitung Graupner FALCON 12 - S1035 (Seite 14 von 36) (Englisch)

747934

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

14 / 36

S1035_Falcon_12_jh_V1

Gyro assignment

Aileron servos:

You should enter the value 2 in this line if your model has two aile-

ron servos. In this case the gyro for channel (servo) 2 also acts on

servo 5. If the ailerons are also used as ﬂaperons or speedbrakes,

gyro suppression is based on the sum of both channels.

Note

The servo reverse seng must be the same for both aileron servos,

i.e. either both ‘normal’ or both ‘reverse’. If this is not possible, on

no account should you reverse one servo in the transmier menu.

The only opon is to re-install it in the model by turning it round

physically.

However, if your model is ﬁed with programmable servos (e.g.

Graupner DES, HVS or HBS types - see the instrucons for the update

program ‘Firmware_Upgrade_grStudio - then it is possible to

reverse the direcon of ro

taon at the servo itself.

Please read the installaon notes on page 8 of these instrucons.

The ﬁrst step is to deﬁne the three gyro axes and the orientaon of

the receiver. This is accomplished by switching on the transmier

and model, and selecng ‘DO SETUP: yes’ in the receiver’s ‘Gyro set-

ngs’ menu.

 Now move the sck for any control surface to full travel (in the

servo display at least 25%) in the indicated direcon; in the fol-

lowing example we use the aileron channel.

 The detected axis (aileron) is highlighted (black background). (In

the receiver’s default state the value for all axes is shown as ‘+0’;

the axes can also be set manually to ‘+0’. 0 = inacve)

 Now turn the model through at least 45° in the direcon corre-

sponding to the sck movement. For example, if you moved the

aileron sck to the le, you must simulate a le turn with the

model -> move the le wing down through at least 45°.

 This process deﬁnes the one axis and direcon; now you must

repeat the procedure for the other two axes.

 The gyro axis 1, 2 or 3 is now displayed in the ‘Aileron / Elevator

/ Rudder’ display; a negave preﬁx will appear if servo reverse is

acvated.

 Once all three axes are deﬁned, the display automacally reverts

to ‘New seng: no’.

   

  

  

  

 

 

   

  

  

  

 

 

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner FALCON 12 - S1035 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner FALCON 12 - S1035

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info