Bedienungsanleitung Graupner MC 22S (Seite 129 von 180) (Englisch)

467112

129

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

129

Controlling the electric motor and butterﬂ y (crow) system using the Ch1 stick

(Butterﬂ y / crow system as landing aid: ailerons up, ﬂ aps down)

Example 4

If you set the Expert Mode line in the »Basic set-

tings« menu to “no” (the default setting) before you

set up the appropriate model memory, please note

that the multi-function menu for this model memory

will only display a limited number of functions. In the

menu …

»Suppress Codes« (page 49)

-ODELSELECT #OPY%RASE

"ASESETUPMODEL -ODELTYPE

3ERVOADJUSTMENT #ONTROLADJUST

$UAL2ATE%XPO #HANNELCURVE

3WITCHDISPLAY #ONTROLSWITCH

3UPPRESS

4/'

you can select the menu points required for this ex-

ample using the rotary control, and include them

again in the current model memory with a brief press

on the rotary control.

Since this example really represents a procedure for

“experts”, perhaps this is the time for you to consider

setting the expert mode to “yes”, so that in future all

the menus of the mc-22s will be available to you from

the outset when you set up further “free” memories.

However, before we start the programming of this

fourth example, and turn our attention to expanding

the basic programming we have already discussed,

we need to consider brieﬂ y the position of the thrott-

le / brake stick at “motor OFF” or “brake OFF”. Usual-

ly the Ch1 stick is moved forward to open the throttle,

and back (towards you) to extend the brakes.

However, if you adopt this “classic” conﬁ guration, and

switch, say, from “motor OFF” (stick “back”) to the bra-

king system, “full brake” would immediately be ap-

plied, and vice versa: if you switch from “brakes re-

tracted” to power, this would instantly switch to “full

power”.

These inter-connected effects are deﬁ nitely not desi-

rable, and to avoid them we recommend that you po-

sition the “zero point” of both systems so that they

coincide. A “glider guider” would normally prefer the

“forward” setting, while a “power man” would probably

opt for “back”. The mc-22s allows either, so the choice

is up to you.

In the menu …

»Model type« (page 52)

M o t o r T h r . m in f r o n t

T a il t y p e N o r m a l

A il e r o n / c a m b e r f la p s 1 A I L

B r a k e

O f f s e t + 1 0 0 % E n t e r 1

S E L

M O D E L T Y P E

… move ﬁ rst to the “Motor” line and set the thrott-

le minimum position to “forward” or “back”. In the fol-

lowing programming example we assume that “motor

OFF” and “brake OFF” are both set to “forward”.

Note:

If you choose “Throttle min. forward / back”, the trim

is then only active at the “idle” end of the travel, i.e. it

does not affect the whole travel of the Ch1 stick as it

would if you were to enter “none”. However, since the

Ch1 trim is generally not used for electric power sys-

tems, this is not very important. More important, ho-

wever, is the fact that …

… setting the motor to “none” automatically

disables the “Throttle too high” power-on war-

ning! For this reason please take great care to set

the Ch1 stick to the correct position before you

switch on the receiving system.

Set the “Tail” type to suit your model; in our case “nor-

mal”.

In the “Ailerons / ﬂ aps” line enter the appropriate

number of aileron and ﬂ ap servos.

In the last line leave the choice of “Throttle min. back”

or “none” at the default settings. However, if you op-

ted for “Throttle min. forward”, select the “Brake”

line and set the Offset point to “forward”, as de-

scribed on page 52.

The next step is to ensure that the effect of the Ch1

stick on the motor can be switched on and off.

This is carried out by moving to the menu …

»Phase setup« (page 78)

P h a s e 1 N o r m a l

0 . 0 s

P h a s e 2 L a n d i n g 0 . 0 s -

P h a s e 3 0 . 0 s -

P h a s e 4

0 . 0 s -

N a m e S w itc h t im e s t a t u s

S E L

… where you assign “Phase 1” with a brief press on

the rotary control, followed by selecting the name

“Normal” from the list. The asterisk (*) in the right-

hand column indicates which phase is currently acti-

ve. If you have not yet assigned a phase switch, this

will always be Phase 1. For this reason you should al-

ways assign the “Normal” name to this phase. For this

example we suggest that you assign the name “Lan-

ding” to “Phase 2”. You may also wish to enter a sui-

table phase switch transition time at this point.

The second stage is to assign a switch to these ﬂ ight

phases, so that you can switch between the two pha-

ses in ﬂ ight. In this case a simple switch is sufﬁ cient,

although it should be easily accessible so that you

can switch between “Motor” and “Brake” on the lan-

ding approach without having to release a stick. A

Programming examples – Fixed-wing models

Graupner MC 22S Seite 129

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info