Bedienungsanleitung Graupner MC 22S (Seite 132 von 180) (Englisch)

467112

132

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

132

Operating the timers using transmitter controls or external switches

Programming examples – Fixed-wing models

If you have followed the model programming descri-

bed on the preceding pages for Example 1 on page

126 or Example 4 on page 129, or – in contrast to

the programming examples – you are using the Ch1

stick (throttle / brake stick) for power control, then you

can use a control switch to start and stop the stop-

watch automatically.

To assign the desired timer to one of the control swit-

ches G1 to G4, you move to the menu ...

»Timers« (page 82)

M o d e l t im e 0 : 2 0 h

B a t t . t im e 4 : 4 5 h

S t w a t c h 0 : 0 0 0 s G 1

F li g h t t m 0 : 0 0 0 s

T im e r A la r m

S E L S E L S E L

… and select the appropriate line with the rotary con-

trol pressed in. Assign the desired timer to the trans-

mitter control switch you wish to use as described on

page 30.

You should now call up the menu ...

»Control switches« (page 72)

C O N T R O L S W I T C H

G 1 C n t r

0 % = > G 1

G 2 fr e e 0 % = > G 2

G 3 fr e e 0 % = > G 3

G 4 fr e e 0 % = > G 4

S E L

S T O S E L

… and select the line for this control switch with the

rotary control pressed in. Press the rotary control with

the left-hand SEL ﬁ eld displayed in inverse video,

then simply select the corresponding transmitter cont-

rol, e.g. control 1 (= Ch1).

Use the rotary control to shift to the STO ﬁ eld …

… and move the corresponding transmitter control in

the direction of motor “OFF” (e.g. stick back towards

you). Give a brief press on the rotary control to deﬁ ne

the switching point. The right-hand column displays

the status of the switch: above the switching point

the G1 switch (in our example) is “closed”, below that

point it is “open”. The stopwatch in the basic display

now starts when you move the Ch1 stick towards full-

throttle, and stops when you pull the stick back again.

In contrast, if you are controlling your motor with an

external switch as described in Example 2 or 3, you

do not need the control switches described above. It

is quite sufﬁ cient simply to assign the stopwatch to

the same switch, so that the timer starts running auto-

matically when the motor is switched on.

Tip:

When using an electric motor, the motor run is usu-

ally limited by the capacity of the battery, and in this

case you would normally set the stopwatch to “count

down”. Simply enter the maximum permitted motor

run in the “Timer” column, e.g. “5 min.”, and set the pi-

ezo buzzer to emit warning tones shortly before the

permissible time has elapsed, e.g. “30 sec” before-

hand.

M o d e l t im e 0 : 3 3 h

B a t t . t im e 5 : 0 3 h

S t w a t c h 5

: 0 0

3 0 s G 1

F li g h t t m 0 : 0 0 0 s

T im e r A la r m

S E L S E L S E L

With the stopwatch halted, press the CLEAR button

from the basic display, so that the stopwatch switches

to the “Timer” function. The timer can now be started

and stopped using the motor control stick.



Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MC 22S Seite 132

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info