Bedienungsanleitung Graupner MC 22S (Seite 140 von 180) (Englisch)

467112

140

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

140

»MIX-only channel« (page 108)

M I X O N L Y C H A N N E L

M I X o n l y

n o r m a l

1 2

3 4

5 6

7 8 9 1 0

1 1 1 2

… so that the associated servo is not also operated

by the elevator stick!

Many years ago the author operated a model delta

with the mc-20, programmed exactly in this way, with

a butterﬂ y (crow) system as landing aid, exploiting the

“Brake  5 aileron” and “Brake  6 ﬂ aps” wing mi-

xers to provide complete compensation for pitch trim

changes. In this case the term “ailerons” means the

outboard wing control surfaces, and “ﬂ aps” the in-

board pair of control surfaces. To achieve the same

effect with the mc-22s, move back to the menu …

»Wing mixers« (page 84)

… and enter the values for the up-aileron travel and

the down-ﬂ ap travel in the “Brake  5 aileron” and

“Brake  6 ﬂ aps” lines in such a way that the pitching

moments which occur in ﬂ ight cancel each other out,

Programming examples – Fixed-wing models

i.e. the model’s ﬂ ight attitude remains stable. Howe-

ver, do take care to allow the control surfaces enough

“elbow-room” for the elevator function: this means,

don’t exploit the full servo travel for the butterﬂ y / crow

system alone.

You can ignore all the other settings in this menu.

A modern sweptback ﬂ ying wing can also be opera-

ted in the same way. Many of these models also fea-

ture inboard and outboard control surfaces: the for-

mer forward of the Centre of Gravity, the latter aft of it.

Deﬂ ecting the inboard control surface(s) down incre-

ases lift and produces an up-elevator effect. Deﬂ ec-

ting them up creates the opposite effect. In contrast,

the outboard ailerons have the reverse effect: a down-

deﬂ ection produces a down-elevator effect, and vice

versa. In this case there are really no limits to what

you can achieve with careful thought and the sophisti-

cated mixers of the mc-22s. This could extend to set-

ting up curve mixers which pass just a small degree

of up / down travel to the outboard pair of control sur-

faces, and only at fairly extreme stick travels. For his

own model this writer uses a curve mixer deﬁ ned by a

total of four reference points, i.e.:

In this example the two reference points 1 and 2 are

set to 0%, the left end-point to +60%, and the right

end-point to -65%; the curve is then rounded by pres-

sing the ENTER button.

Please note that you should be extremely careful

when setting differential travel with such a conﬁ gura-

tion, regardless of the type of servo arrangement you

are using. This is because differential travels tend to

produce an asymmetrical elevator effect on a tail-less

model, rather than the desired adverse yaw reduction.

For this reason it is advisable to start with a differenti-

al setting of 0%, at least for the ﬁ rst few ﬂ ights. When

you are familiar with the model and feel the need to

experiment, it may then be feasible under certain cir-

cumstances to try differential settings deviating from

zero.

For larger models it may be advisable to install wing-

lets ﬁ tted with rudders, i.e. small vertical surfaces at

the wingtips. If these are actuated by two separate

servos, the rudder signal can very easily be “split” by

using a mixer in the menu ...

»Dual mixers« (page 110)

… in which case you can also apply “split” or differen-

tial travel, with the second rudder servo connected to

a free receiver output socket. If you have programmed

the “Delta / ﬂ ying wing” tail type at an earlier stage,

receiver output “5” should still be free. If you have se-

lected the “normal” tail type, output “3” (ELE) should

still be free; this is the one we will use in the following

example.

Select the »MIX-only channel« menu (see above),

or the »Control adjust« menu (if the second ser-

vo is connected to one of the outputs 5 … 12), and

de-couple the “wrong” control function from the cont-

rol channel to which you have connected the second

rudder servo.

The differential travel is necessary in this case, since

the outside rudder turns through a larger radius than

the inside rudder when the model is ﬂ ying a turn; this

is broadly analogous to the effect of front wheel toe-

A il e r o n d i f f e r e n c e + 0 %

F la p d if f e r e n c e + 0 %

A il e r o n s 2 > 4 R u d d e r + 0 %

A il e r o n s 2 > 7 F la p s +

5 0 %

B r a k e > 3 E le v a t o r + 0 %

B r a k e > 6 F l a p s - 5 0 %

B r a k e > 5 A i le r o n s - 6 0 %

E le v a t o r 3 > 6 F la p

s + 0 % + 0 %

E le v a t o r 3 > 5 A il e r o n + 0 % + 0 %

F la p s 6 > 3 E le v a t o r + 0 % + 0 %

F la p s 6

> 5 A i le r o n s + 0 % + 0 %

R e d u c t io n o f d if f . + 0 %

S E L

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MC 22S Seite 140

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info