747993
30
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
30 / 80 33028_mc_28_Teil2_jh
"Type"
In this column you can select the control setting for this channel to
act globally "G" or according to the phase "PH". If the control is
assigned specifically to the phase, the related phase must be active.
The phase name will be shown in the second line from the bottom
of the display.
"fr"
Here you can assign the desired proportional control. “fr” (free) will
be displayed if no control is assigned. Here you can assign propor-
tional controls only, no switch. Assign a control by pushing the SET
button. The abbreviation of the selected control will appear.
"SEL "
Here you can assign the desired switch. If a proportional control is
already assigned, the proportional control will be deactivated and a
second switch in the column can be assaigned. Tap again on SET, you
can also assign logical switches or normal switches.
Assign a switch by pushing the SET button. The abbreviation of the
selected switch will appear.
Delete proportional control or switch:
Use the SET button to select the desired field
Tap on the selection buttons  t u or   at the same time
"Offset"
Here, move the center of the channel in a possible range from -125%
to + 125%.
Symmetrical travel setting:
Move the related control element (control stick, proportional con-
trol or switch) into a position in which both sides of the travel adjust-
ment are surrounded by the marking frame. Set with the SET button
and the selection buttons.
Asymmetrical travel setting:
Move the related control element (control stick, proportional con-
trol or switch) into a position in which the single side of the travel
adjustment is surrounded by the marking frame. Set with the SET
button and the selection buttons.
In5
offset
0%
0%
0%
–––
0%
In6
In7
In8–––
–––
–––
GL
GL
GL
GL
typ
Normal
fr
fr
fr
fr
SEL
In5
offset
0%
0%
0%
–––
0%
In6
In7
In8–––
–––
–––
GL
GL
GL
GL
typ
Normal
fr
fr
fr
fr
SEL
Move desired
control adj.
In5
offset
0%
0%
0%
–––
0%
E6
E7
E8 –––
–––
–––
GL
GL
GL
GL
typ
Normal
fr
SD2
fr
fr
SEL
Move desired switch
to ON position
(ext. switch: SET)
In5
offset
0%
0%
0%
–––
0%
In6
In7
In8–––
–––
GL
GL
GL
GL
typ
Normal
fr
fr
fr
3
2
30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Graupner MC-28 4D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info