747993
43
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
43 / 80
33028_mc_28_Teil2_jh
Programming of the wing type
Model type: "1AIL"
If "1AIL" in the "Aile/Flap" line of the "Model type" menu has been
entered, the "Mixer menu" of your transmitter corresponds to the
figure on the left. All available parameters can be changed depend-
ing on the phase, egardless of the selected combination of ailerons
and flaps.
Brake setting
The "Brake settings" menu is not shown if “yes” has been entered in
the "Model type" menu "Motor on CH1 front / rear" and in the col-
umn "Motor" of the "Phase setting" menu for the currently active
phase. With one aileron servo in the model neither a Butterfly nor a
differentiation reduction can be enabled. There are no further set-
ting options here besides the "Travel" in the submenu "Elevator
curve".
For detailed information on how to set a curve mixer, see the "Throt-
tle curve" menu item.
Aile -> Dir
The rudder also moves to an adjustable degree when the aileron is
operated. The adjustable rudder can compensate for the negative
torque in conjunction with aileron differentiation. The combination
smoothes curves in flight. The rudder remains separately controlla-
ble. The setting range of ±150 % enables you to adapt to the direc-
tion of deflection. Optionally, this mixer can be turned on and off by
one of the positioning switches or controls. The model can be con-
trolled exclusively using the aileron or rudder.
Model type: "1AIL 1FLAP"
The “Mixer menu” of the transmitter corresponds to the figure on
the left if you have entered "1AIL 1FLAP" in the "Aile/Flap" line of the
"Model type" menu. All available parameters can be changed
depending on the phase, regardless of the selected combination of
ailerons and flaps,.
Brake setting
The "Brake settings" menu is not shown if “yes” has been entered in
the "Model type" menu "Motor on CH1 front / rear" and in the col-
umn "Motor" of the "Phase setting" menu for the currently active
phase.
The flap is lowered when a suitable value is entered in the "Butter-
fly" line. This function is enabled by the brake control (Throttle con-
trol stick). Move the brake control to the stop in the brake position.
Then, after briefly pressing the SET button, use the selection keys to
set a suitable value. To achieve sufficient braking, the flap must be
lowered as far as mechanically possible.
Elevator CURVE
Apply a correspondingly automatic effective admixture to the eleva-
tor. This prevents you from having to intervene with the elevator
Brake settings
AI 0%
Wing mixers
–––
RU
Normal
Input
Output
Point ?
–100%
0%
0%
Brake
normal
Ele
Curve off
Normal
Brake settings
AI 0%
Wing mixers
EL FL 0%
0%
–––
–––
RU
Normal
FL EL 0%
0% –––
Ele curve
Brake settings
Butt.
Normal
0%
FL
Input
Output
Point ?
–100%
0%
0%
Brake
normal
Ele
Curve off
Normal
43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Graupner MC-28 4D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info