747993
56
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
56 / 80 33028_mc_28_Teil2_jh
Trim X-axis function
This function can be activated by tapping the left-hand t or the right
u selection button of the right-hand touch panel while the value
field is active. You can then move the active point horizontally or ver-
tically using the selection buttons.
Deleting support points
Place the marker frame in the "Point" line and briefly tap the SET but-
ton. The value field displayed is highlighted. Then set the vertical line
through the control of the mixer input to the support point. The sup-
port point number and the corresponding support point value are
displayed in the "Point" line. Now simultaneously tap on the selec-
tion buttons t u or   of the right-hand touch pad. The
selected support point is deleted and the numbering of the remain-
ing support points is updated. The support points "L" and "H" cannot
be deleted.
Rounding off the curve
The angled curve profile can be automatically rounded off simply by
pressing a button. Set the curve value from "off" to "on" (or vice
versa). Close this process by pressing the SET button or the ESC but-
ton.
MIX act. / Phase
In this menu you can phase-specifically deactivate and activate the
"free mixers" of the previously described "free mixers" menu. Switch
to the desired phase and page in this menu with the selection keys.
The mixers of the "free mixers" menu are displayed line by line. If in
the right colum, the respective mixer is set with the selection keys
"--" the mixer is deactivated in the phase displayed in the lower part
of the display. At the same time it is dimmed in the menu "free
mixer".
Only mix channel
In this menu, the direct control/servo connection can be separated
depending on the phase. If a channel is set to "only mix", this chan-
nel can only be used for one mixer. The channel can no longer be
used for the output. This applies only to the phase that is currently
active. In the "normal" position, the control signal of the channel
acts on the mixer and on the output.
+35%
–37%
Input
Output
Point 2
C.Mix 9
normal
Kurve aus
810
–55%
Trim X axis
0%
–12%
Input
Output
Point ?
C.Mix 9
normal
Curve
810
0%
on
LinearM1
LinearM2
LinearM3
6EL
C1 EL
LinearM4
3 8
SEL
yes
SEL
yes
yes
yes
Mix act. in phase
normal
MIX-only channel
only
normal
1 2 3 456
56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Graupner MC-28 4D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info