Bedienungsanleitung Graupner MC-28 4D (Seite 60 von 80) (Englisch)

747993

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

60 / 80 33028_mc_28_Teil2_jh

Trim memory

Storage of the trim position

In the left column (POS) the value of the trim is shown. Now tap the

SET button. The trim value is transferred to the memory. The trim

value is now displayed in the "SET" column on the right side. The bar

display in the main display shows again the center position.

To delete the stored trim value, tap the selection keys t u or 

on the selected line.

Telemetry

Through the telemetry menu, you can perform receiver settings in

real time. Displays and settings of optionally connected telemetry

sensors can be retrieved and programmed. The connection to the

receiver is maintained by the feedback channel of the HoTT receiver.

TEL.RECEI. - Here set from which receiver the telemetry data is to

be processed. Set the possible settings for the following menu item.

SETTINGS & DATAVIEW - If you select this item, you will open the

menus for settings of the receiver or the sensors connected. Select

the desired sensor or module through the selection keys . (See

the manual of the sensor or of the module)

SENSOR: List of the sensors connected and detected (only display,

no manual selection possible)

DISPLAY RF STATUS - Top row: Level of channels 1 … 75 coming

from the receiver of the 2.4 GHz band in dBm to the transmitter. Bot-

tom row: Level of channels 1 … 75 coming from the transmitter of

the 2.4 GHz band in dBm to the receiver.

SELECT ANNOUNCE - In the first line, assign a switch and set the

repetition time to start the voice output. In the next line "NEXT

ANNOUNCE" assign a switch to switch the announcements through.

In the "VARIO" line, assign a separate switch for the vario signals.

Select automatical (AUTO) or a specific sensor (GPS, EAM, GAM)for

the sounds.

Tap the SET button in the "TRANSMITTER, RECEIVER" line. In the list

that is now displayed, set which messages should be active for the

transmitter or receiver.

RX DATA - Here set how the transmitter responds to the receiver's

back channel (telemetry transmission). Use this function if the back

channel of the receiver is influenced by the back channel of another

receiver.

In the "ON" position the telemetry signals are processed continu-

ously. In the "1" position, the telemetry signals are processed with a

slight delay; the telemetry signals are processed in a very delayed

manner in position "10".

Trim memory

AILE

ELEV

RUDD

0% 0%

POS SET

CH1 0% 0%

Telemetry

SETTING & DATA VIEW

SENSOR

RF STATUS VIEW

VOICE TRIGGER

TEL.RCV BIND. 1

RX DATA ON

ALARM SETTING

RX–S QUA: 100%

RX–S ST : 100%

TX–dBm: 33dBm

RX–dBm: 33dBm

RX–SPG.:4.8 TMP

V–PACK: 10ms

CH OUTPUT TYPE:ONCE

GENERAL MODULE

ELECTRIC AIR.MOD

VARIO MODULE

GPS

RECEIVER

ESC

RX–S QUA: 100%

RX–S ST.: 100%

TX–dBm: –33dBm

RX–dBm: –33dBm

RX–SPG.:4.8V TMP

V–PACK: 10ms

CH OUTPUT TYPE:ONCE

M–RX V :4.6V +22°C

R100%

T –40

E 10

R –51

4.8Vc

S 90%

4.8Vm 0123456789ABCDE

VOICE TRIGGER

REPEAT 10SEC

TRIG

TRANSMITTER

RECEIVER

–––

VARIO AUTO –––

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MC-28 4D Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info