747993
69
Zoom out
Zoom in
Vorherige Seite
1/80
Nächste Seite
69 / 80
33028_mc_28_Teil2_jh
Info display
This menu shows information about the transmitter and the SD card.
The date and time can be set here.
RFID - Identity number of the transmitter
Firmware version - shows the version of the transmitter firmware
Dat. - Date (also used for log files)
Time - Time (also used for log files)
SD card - shows the capacity of the inserted SD card
Available - shows the free space on the SD card
Percentage display - used space as % of the SD card
Digital trim / Throttle switch-off trim (function)
A special function is integrated in the digital throttle trim, enabling
the adjustment of the idle speed of an engine. This "switch-off trim"
is effective only in the range of -1 to -100% and only if front or rear is
entered in the “Motor type CH1” line in the "Model type" menu.
The throttle trim has a special "cut-off trim" intended for engines.
First set the motor to safe idle with the trim.
A further marking remains at the end position in the display if the
throttle trim is moved from this position to the end of the trim travel
in the "motor stop" direction.
Then simply push the trim once more in the "higher throttle" direc-
tion to reset the trim to the last idle setting.
With the model type "Heli", the throttle trim in combination with the
"throttle limit function" has a further property. The throttle trim acts
as an idle trim on the throttle servo if the throttle limit control is in
the range -1 to -100%. The indication of the idle trim is visible in the
display.
The position indicator ( ) and a predefined idle position are dimmed
when the throttle limit control is in the range 0 to + 100%.
The throttle trim works only on the throttle, not on the pitch servos.
Note that the heli throttle servo must be connected to the output 6
of the receiver.
RFID
firmware ver.
date
time
SD-CARD
available
1.234
3623MB
92%
ABCDEF12
2016/09/17(Sa )
18:19:20s
3896MB
GRAUBELE
#01
3:33h
S
L
K78
0:00
0:00
RX0.0V
5.2V
trim position
2.4
C1 trim lever
M
Trimming in
GRAUBELE
#01
3:33h
S
L
K78
0:00
0:00
RX0.0V
5.2V
last idle position
2.4
M
Motor-OFF position
actual
trim position
Trimming in
Throttle limiter in start position
GRAUBELE
#01
3:33h
S
L
K78
0:00
0:00
RX0.0V
5.2V
M2.4
Throttle limiter in release position
69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Graupner MC-28 4D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info