Bedienungsanleitung Graupner MX-16 HoTT (Seite 88 von 200) (Englisch)

467107

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Program description: base settings - model helicopter

cess from virtually any menu position by simultaneously

touching the  and  buttons of the left-hand touch-

key - refers exclusively to the “control channels”, i. e. the

outputs are NOT swapped over.

output

Use the arrow buttons  of the left or right-hand

touch-key to select the servo / output combination you

wish to change, then touch the central SET button of the

right-hand touch-key. Now you can assign the desired

servo (S) to the selected output using the right-hand

arrow buttons, and conﬁrm your choice with SET … or

alternatively touch the  or  buttons of the right-

hand touch-key (CLEAR) simultaneously to revert to the

default sequence.

Please note that any subsequent changes to servo

settings, such as servo travel, Dual Rate / Expo, mixers

etc., must be carried out according to the original

(default) receiver socket sequence.

Typical application:

In the helicopter program of the mx-16 HoTT the

outputs for one collective pitch servo and the throttle

servo have been interchanged compared to all earlier

GRAUPNER/JR mc-systems. The throttle servo is now

assigned to receiver output “6” and the collective pitch

servo to output “1”. However, you may wish to retain the

earlier conﬁguration.

output

S 6

output

Note:

It is also possible to distribute the control functions

amongst as many receivers as you wish, using the

channel-mapping function in the mx-16 HoTT’s

integral Telemetry menu, or even to assign the same

control function to multiple receiver outputs. However,

we strongly recommend that you use only one of the two

options, as a combination will soon lead to confusion.

rx bind (Bound receiver)

Graupner|SJ HoTT receivers have to be “instructed” to

communicate exclusively with a particular model (i. e.

model memory) of a Graupner|SJ HoTT transmitter. This

process is known as “binding”, and is only necessary

once for each new combination of receiver and model. It

can be repeated at any time.

Important note:

When carrying out the binding procedure, please

ensure that the transmitter aerial is always an

adequate distance from the receiver aerials: keeping

the aerials about 1 m apart is safe in this respect.

Otherwise you risk a failed connection to the down-

link channel, and consequent malfunctions.

“Binding” multiple receivers to one model

If necessary, it is possible to bind more than one re-

ceiver to a single model. This is accomplished by initially

binding the receivers individually, as described in the

next section.

When operating the system, please note that only

the receiver which was bound last will establish a

telemetry link to the transmitter. For this reason all te-

lemetry sensors installed in the model must be connect-

ed to this receiver, since only the last bound receiver

is able to transmit their data via the down-link channel.

The second, and all other receivers, run in parallel to

the receiver last bound to the transmitter, but completely

independently of it; they operate in Slave mode with the

down-link channel switched off.

“Binding” transmitter and receiver

Use the arrow buttons  of the left or right-hand

touch-key to move to the “rx bind” line:

phase 2

phase 3

hover

speed

autorotat.

receiv out

rx bind

–––

If you have not already done so, switch on the power

supply to your receiver now: the red LED on the receiver

ﬂashes.

Press and hold the SET button on the receiver until,

after about three seconds, the red-ﬂashing LED starts to

ﬂash red / green; this will last for a further three seconds.

You can now release the SET button on the receiver.

The receiver is in Bind mode as long as the LED ﬂashes

red / green.

Brieﬂy touch the central SET button of the right-hand

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info