Bedienungsanleitung Graupner MX-16 HoTT (Seite 108 von 200) (Englisch)

467107

108

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

108

Program description: wing mixers – ﬁxed-wing model

Fixed-wing mixers

–––

ail

diff aile.

rudd

flaps

brak

elev

flap

aile

elev

flap

aile

elev

flap

diff–red

aile

diff flaps

(The display varies according to the information you

have entered in the “Motor at Ch 1” and “Ail / Flap” lines

in the “Base settings” menu. The selection above shows

the maximum number of options, and equates to the

setting “No (motor)” and “2AIL 2FL”).

The mx-16 HoTT transmitter’s program contains a se-

ries of pre-programmed coupling functions, and all you

have to do is set the mixer ratios and (optionally) assign

a switch. The number of pre-programmed mixer func-

tions in the mixer list will vary according to the pre-set

“model type” (tail type, number of wing servos, with or

without motor - see the section starting on page 74). For

example, if your model is not ﬁtted with camber-chang-

ing ﬂaps, and you have not entered any ﬂap servos in

the “Base settings” menu, the software automatically

suppresses all the ﬂap mixers, as are the “Brake  NN

*“ mixers if you enter “Idle forward” or “Idle back” in the

“Motor at Ch 1” line. This makes the menus clearer and

easier to understand, and also avoids potential program-

ming errors.

What is a mixer?

The basic function

In many models it is often desirable to use a mixer to

couple various control systems, e. g. to link the ailerons

and rudder, or to inter-connect a pair of servos where

two control surfaces are actuated by separate servos. In

all these cases the signal which ﬂows directly from the

“output” of a transmitter stick to the associated servo

is “bled off” at a particular point - this effect can also

be “concealed” in transmitter control options such as

“D/R Expo” or “Transmitter control settings” - and

the derived signal is then processed in such a way that

it affects the “input” of another control channel, and

therefore eventually another receiver output.

Example: V-tail mixer

4 8 V

C 577

B s N 410

Se v

4 8 V

C 577

es N 410

V-tail mixer

Control function inputs

Control channels

(receiver outputs)

Elevator stick

Rudder stick

Right rudder / elevator

Left rudder / elevator

Rudder

Elevator

Rudder

Elevator

The mx-16 HoTT transmitter software contains a

large number of pre-programmed coupling functions as

standard, designed to mix together two (or more) control

channels. The mixer required in this example is supplied

“ready-made” in the software, and just has to be acti-

vated in the “tail” line of the “Base settings” menu in the

form of “V-tail”.

The software also includes three freely programmable

linear mixers in the ﬁxed-wing and helicopter programs,

all of which can be used in each model memory.

* NN = Nomen Nominandum (name to be stated)

For more information please refer to the general notes

on “Free mixers” in the section of this manual starting on

page 126.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 108

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info