Bedienungsanleitung Graupner MX-16 HoTT (Seite 133 von 200) (Englisch)

467107

133

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

133

Program description: servo position

Servo display

Use the arrow buttons of the left or right-hand touch-key

to leaf through to the “Servo display” menu point of the

multi-function menu:

mod.mem.

servo set.

D/R expo

wing mixer

base sett.

contr set.

phase trim

free mixer

basic sett

fail-safe telemetry

servo disp

Open the menu point by touching the central SET button

of the right-hand touch-key.

However, this visual display of the current servo posi-

tions can be called up not only by selecting this menu,

but also directly by simultaneously pressing the buttons

 of the left-hand touch-key from the transmitter’s

basic display, and also from almost any menu position.

Touching the central ESC button of the left-hand touch-

key returns you to your starting point again.

–100%

+100%

The current position of any servo is displayed in bar-

chart form, which takes into account the transmitter con-

trol and servo settings, the Dual-Rate / Expo functions,

the interaction of all active mixers etc., within the range

-150% to +150% of normal travel. 0% corresponds

exactly to the servo centre position. The servo display

provides a quick method of checking your settings, with-

out having to switch on the receiving system. However,

this does not relieve you of the need to check all your

programming steps carefully on the model before oper-

ating it for the ﬁrst time, as this is the only safe method

of excluding possible programming errors.

The display is based on the following scheme for

ﬁxed-wing models:

Bar 1 = throttle / brake servo

Bar 2 = aileron or left aileron

Bar 3 = elevator

Bar 4 = rudder

Bar 5 = right aileron

Bar 6 = (left) ﬂap / free channel

Bar 7 = right ﬂap / free channel

Bar 8 = free channel / second elevator servo

and for model helicopters:

Bar 1 = collective pitch or roll (2) or pitch-axis (2) ser-

Bar 2 = roll (1) servo

Bar 3 = pitch-axis (1) servo

Bar 4 = tail rotor servo (gyro)

Bar 5 = pitch-axis (2) servo / free channel

Bar 6 = throttle servo or speed controller

Bar 7 = gyro gain / free channel

Bar 8 = speed governor / free channel

Note:

Please note, however, that the servo display always •

applies to the original servo sequence, i.e. it takes

no account of any outputs swapped over in the “Re-

ceiver output” menu of the “Basic model settings”

menu, nor changes made directly at the receiver us-

ing the “Telemetry” menu.

The number of channels shown in this menu corre-•

sponds to the eight control channels available at the

mx-16 HoTT transmitter. However, the actual number

of channels you can use varies according to the type

of receiver in the model, and to the number of servos

connected to the receiver; the number may therefore

be much smaller.

Use this display during the model programming pro-•

cedure, so that you can immediately check all the

settings at the transmitter. However, this does not re-

lease you from the responsibility to check all the pro-

gramming steps on the model itself before operating

it for the ﬁrst time, in order to exclude the possibili-

ty of errors!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 133

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info