Bedienungsanleitung Graupner MX-16 HoTT (Seite 137 von 200) (Englisch)

467107

137

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

137

Program description: Telemetry menu

Telemetry

The “Telemetry” menu provides a means of calling up

receiver settings, and settings for any telemetry sen-

sors connected to the system, and programming them

in real-time. The transmitter is linked to the receiver via

the downlink channel which is an integral feature of the

HoTT receiver.

If Y-leads are used, a maximum of four sensors can

be connected to the Telemetry sockets of the following

receivers; this assumes that the current ﬁrmware is

loaded: GR-12S HoTT (Order No. 33505), GR-12 HoTT

(Order No. 33506), GR-16 (Order No. 33508), GR-24

HoTT (Order No. 33512) and GR-32 DUAL (Order No.

33516).

Since the system can be updated by the user, the as-

sociated “Telemetry” menus can constantly be kept up-

to-date, and expanded with the introduction of additional

functions or languages in future.

Note:

If you register your product under https://www.graupner.

de/en/service/product_registration you will automatically

be informed about new updates by e-mail.

Before updating the transmitter software you should

always back up all occupied model memories to a

compatible laptop or PC in order to avoid a possible loss

of data.

As mentioned earlier, ﬁrmware can be updated and

data backed up via the transmitter’s PC socket using the

USB interface, Order No. 7168.6, and the connecting

lead, Order No. 6466.S, which are supplied in the set as

standard. This requires the use of a PC running Win-

dows XP, Vista or 7 as operating system.

The programs required for this and related information

can be found in the Download area for the correspond-

ing products at the website www.graupner.de. We

always recommend that you load the latest ﬁrmware into

your equipment, to ensure that your system is constantly

kept up-to-date.

Important information:

These instructions cover the functions available at •

the time of going to press.

As mentioned in the sections entitled “Binding mul-•

tiple receivers” on pages 80 and 88, it is possible to

bind more than one receiver per model. However, in

subsequent operations only the receiver which

was bound last is able to make a telemetry con-

nection to the transmitter. On the other hand, this

also means that only the last bound receiver can be

addressed using the Telemetry menu. You may there-

fore need to change the binding sequence before you

can enter settings which relate to a particular receiv-

er.

When setting up the radio control system, please •

ensure at all times that the transmitter aerial is

an adequate distance from the receiver aerials.

A safe distance is about one metre. If you ne-

glect this, you risk interference with the downlink

channel, and consequent malfunctions.

Since the transmitter and receiver only exchange te-•

lemetry data after each fourth data packet, data

transmission inevitably requires a certain amount of

time, which means that there will be some delay in

responding to button-presses and set-up changes.

This does not constitute an error.

Changes to model and sensor programming must •

only be carried out when the model is on the ground.

Do not make any alterations unless the motor is

switched off and the ﬂight battery is disconnected.

If you ignore this, unwanted effects of programming

changes cannot be excluded.

For example, if you accidentally initiate an active ser-

vo test at the receiver, the model could crash and

cause personal injury or property damage. Please

see the Safety Notes on pages 4 … 7 of this manual

and the various individual instructions.

All settings which you enter using the “• Telemetry”

menu, such as Fail-Safe, servo direction, servo trav-

el, mixer and curve settings etc., are stored exclu-

sively in the receiver, and are therefore carried over

if you install the receiver in a different model. For this

reason we strongly recommend that you re-initial-

ise your HoTT receiver if you wish to use it in another

model; see “Reset” on page 44 and 45.

We therefore recommend that you program directions •

of servo rotation, servo travel, mixer and curve set-

tings using only the mx-16-speciﬁc standard men-

us “Servo settings” (page 92), “Free mixers” (page

127) and “D/R Expo” (pages 102 and 104). If you ig-

nore this, the settings may overlap and interfere with

each other; in the most favourable case this can re-

sult in confusion when operating the model, and in

the least favourable case it could cause problems.

The channel-mapping function of the • mx-16

HoTT’s integral “Telemetry” menu can be used to

share out control functions between multiple receiv-

ers in any way, or even to assign the same control

function to several receiver outputs; for example, you

may wish to operate each aileron with two servos in-

stead of just one, etc. Once again we strongly re-

commend that you act as cautiously as possible

when carrying out the programming.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 137

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info