Bedienungsanleitung Graupner MX-16 HoTT (Seite 155 von 200) (Englisch)

467107

155

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

155

Program description: Trainer system

NER / teacher” as soon as a switch is assigned.

The model to be controlled by the pupil must be pro-

grammed completely in a model memory of the mx-

16 HoTT Teacher transmitter, i. e. with all its functions

including trims and any mixer functions. The HoTT re-

ceiver in the model must also be “bound” to the Teacher

transmitter, since it is this transmitter which actually

controls the model in Pupil mode - even in Trainer mode

operations.

The mx-16 HoTT Teacher transmitter MUST ALWAYS

BE SWITCHED ON FIRST. ONLY THEN MAY THE

CONNECTING LEAD BE PLUGGED INTO IT. If you

neglect this, the RF module will not be activated.

The mx-16 HoTT Teacher transmitter can be linked to

any suitable Pupil transmitter - even those operating on

the “classic” 35 / 40 MHz band.

However, if the connection at the pupil end is NOT

made using a two-pole DSC socket, but instead - for

example - using a three-pin Trainer socket from the

Graupner range, the basic requirement for a correct

connection with a Pupil transmitter is that PPM (18

or 24) modulation must ALWAYS be set on the Pupil

transmitter, regardless of the modulation used by

the Teacher transmitter.

Pupil transmitter settings

The model to be controlled by the pupil must be pro-

grammed completely in a model memory of the Teacher

transmitter, i. e. with all its functions including trims and

any mixer functions, and the HoTT receiver in the model

must be “bound” to the Teacher transmitter. In principle,

however, an mx-16 HoTT Pupil transmitter can also be

linked to a Teacher transmitter operating on the “classic”

35 / 40 MHz band.

The Pupil transmitter can be virtually any transmitter

from the former and current Graupner range with at

least four control functions. More information on this is

available in the main FS catalogue, and on the Internet

under www.graupner.de.

Some transmitters will need to be retro-ﬁtted with the

appropriate module in order to act as the Pupil transmit-

ter. This should be connected to the transmitter circuit

board as described in the installation instructions sup-

plied in the set.

Information on the Pupil module required can be found

in the main Graupner FS catalogue and on the Internet

at www.graupner.de.

The Pupil transmitter must be connected to the Teacher

transmitter using the appropriate lead - see next double

page.

The control functions of the Pupil transmitter MUST

act directly on the control channels, i. e. the receiver

outputs, without the intervention of any mixers.

If you are using an “mc” or “mx” series transmitter,

it is best to set up a free model memory in the Pupil

transmitter with the required model type (“Fixed-wing”

or “Helicopter”). Assign the model name “Pupil” to the

memory, and set up the stick mode (Mode 1 … 4) and

“Throttle min. forward / back” to suit the pupil’s prefer-

ence. All the other settings should be left at the appropri-

ate default values. If you select the “Helicopter” model

type, the throttle / collective pitch direction and idle trim

must also be set accordingly on the Pupil transmitter. All

other functions, including mixer and coupling functions,

are carried out by the Teacher transmitter, which trans-

mits them to the receiver in the model.

If you are using an mx-20 or

mc-3 2 HoTT Pupil

transmitter, it is also necessary to match the type of

modulation to the numbers of the control channels to

be transferred; this is carried out in the “DSC output”

line of the “Basic model settings” menu. For example,

“PPM10” modulation carries control channels 1 … 5,

and its signal packet only contains control channels 1

… 5 - but not channel 6. If you also wish the pupil to be

able to use this channel, then you must select a type of

modulation which includes it!

If you are using a “D” or “FM” type transmitter, you

should check the servo directions and stick mode, and

alter them by re-connecting the appropriate leads if re-

quired. All mixers should be switched off or set to “zero”.

When assigning the control functions the usual conven-

tions should be observed:

Channel Function

1 Throttle / Collective pitch

2 Aileron / Roll

3 Elevator / Pitch-axis

4 Rudder / Tail rotor

If you wish to transfer other control functions to the

Pupil transmitter, in addition to the functions of the two

dual-axis sticks (1 … 4), then you will need to assign

additional transmitter controls in the Pupil transmitter’s

“Transmitter control settings” menu to those inputs

which correspond to transmitter control numbers 5 … 8,

as released in the Teacher transmitter’s “Trainer” menu.

Important:

If you forget to assign a transmitter control, then •

the servo or servos concerned will remain in the

centre position when control is transferred to the

Pupil transmitter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 155

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info