Bedienungsanleitung Graupner MX-16 HoTT (Seite 166 von 200) (Englisch)

467107

166

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

166

Programming example - ﬁxed-wing model

First steps in programming a new model

Example: non-powered ﬁxed-wing model aircraft

When programming a new model you should start by

activating the …

“select model” sub-menu (page 70)

… in the “Model memory” menu. Use the arrow buttons

 of the left or right-hand touch-key to select a free

model memory …



free



R08



free



free



free



free



… then touch the central SET button of the right-hand

touch-key. You are now immediately requested to select

the type of model you wish to program.

Sel model type

( empty mod mem )

Since in this example we are setting up a ﬁxed-wing

model, we simply conﬁrm the ﬁxed-wing model symbol

with a brief press on the central SET button of the right-

hand touch-key; the screen now reverts to the basic

display.

Notes:

Naturally you can also use the pre-deﬁned model •

memory 01 for programming your ﬁrst model; this is

the “ﬁxed-wing model” type by default.

Once you have called up the “Model select” option it •

is not possible to interrupt the process, i. e. you must

choose one or other model type. Even if you switch

off the transmitter at this point, you cannot avoid this

select procedure. However, if you make a mistake

you can always correct it simply by erasing the mod-

el memory.

If the battery voltage is too low, you will not be able •

to change model memories for safety reasons. The

screen then displays an appropriate message:

not possible now

voltage too low

Once you have overcome this initial hurdle, you may

need to bind the receiver installed in the model to this

model memory in the …

“Base settings” menu (pages 74 … 81)

This is accomplished by moving to the “rx bind” line:

phase 3

phase 4 landing

speed

–––

receiv out

rx bind

–––

phase 2 takeoff

–––

Note:

When you conﬁrm the model selection the following

message appears in the basic display for a few seconds:

BIND N/A

If you conﬁrm your choice by brieﬂy pressing the SET

button of the right-hand touch-key, you automatically

move to this line:

In this line you trigger the bind process between model

memory and receiver, as described in detail on pages

80. Without this step you cannot address the receiver.

The next step is to press the  arrow button of the

left-hand or right-hand four-way touch-key to move up

into the ﬁrst line, where you can start the actual model

programming in the “mod name” line:

mod name

stick mode

CH8 delay

motor at C1

yes

tail type normal

At this point you can enter the “Model name” by touch-

ing the central SET button of the right-hand touch-key in

order to move to the character table:

0123456789

PQRSTUVWXYZ

model name

;

ABCDEFGHIJKLMNO

GRAUB

You should also check the settings for “Stick mode” and

“Motor at Ch 1” and change them if necessary:

“none”:•

The brake system is “retracted” at the forward posi-

tion of the throttle / brake stick; the “Ch8 delayed” op-

tion and the “Brake  NN*” mixers in the “Wing mi-

xers” menu are activated.

In the “Aileron / ﬂap” line of the “Basic settings”

menu you can select “1AIL”, “2AIL” and “1/2AIL

* NN = Nomen Nominandum (name to be stated)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX-16 HoTT Seite 166

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX-16 HoTT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info