Bedienungsanleitung Graupner MX12 (Seite 79 von 144) (Deutsch, Englisch, Französisch)

30127

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

trim lever has no effect on positions 1 or throttle hold.

Note: Making changes to the throttle trim lever does

not change the input values for any of the points

on the throttle curve; it merely makes adjust-

ments to the engine idle speed postition.

Output value

Graphic display

POINT

P-LOW : Full Slow position P-3 : Stick 3/4 position

P-1 : Stick 1/4 position P-HIGH : Full High position

P-MID : Stick Center position * Point position is fixed

Hovering Throttle Lever Settings

The Hovering Throttle lever increases or decrease the

engine output power for the middle three points set for

the middle three points set for the throttle curve. As

shown in the figure below, use of the hovering throttle

lever shifts the curve upward or downward parallel with

the original curve. Therefore, operation of the hovering

throttle knob does not cause any change to the original

settings of the throttle curve.

The throttle trim range will affect the throttle curve as

shown.

The adjustable range of output using the hovering thrott-

le lever is approximately +/- 9%.

Note: The Hovering Throttle has no effect on flight

mode switch position 1.

Throttle Stick

Function mode HELICOPTER

Pitch Curves

Function mode HELICOPTER 31

Hovering Throttle Knob

Operating Range (Parallel)

Output Value

P-HIGHP-MIDP-LOW

Throttle Trim

Operating Range

Pitch Curves

Adjustment of the pitch curve is very similar to the thrott-

le curve adjustment described in the preceding section.

A thorough understanding of the Throttle Curve Section

will make pitch curve adjustment easier to understand.

There are three independent types of pitch curves

available: Normal, Stunt, and Hold. Each pitch curve

contains five adjustable points: LOW 1, MID 3, and

HIGH.

Note: The pitch curve for the Throttle Hold function

can only be set if this system is activated.

Flight Mode SW position

Graphic display

Output position

Stick position

Go to Revolution

Mixing menu

Go to Throttle Curve

Select function to

change

Change Value/Switch

selection

Reset POS value to

0 or Inhibit function

Accessing the Pitch Curve Function

1. Place the transmitter power switch in the ON positi-

on.

2. Press the Down and Select keys simultaneously

to enter the Function mode.

3. Press either the Up and Down key until PITCH

appears in the top of the LCD.

Note: Use NORMAL for hover curses and STUNT for

stunt curves. We will concentrate on the ho-

vering curve during this example.

4. Press the Select key to select the point of the curve

you want to change.

5. Press either the (+) or (-) key to change the value of

the current curve point. The range of each point is

0-100% in 0.5% intervals.

Note: In each curve, the factory setting INH indicates

Inhibited for points 1 and 3. These values are

25% and 75% respectively, if no value changes

are made to any other points. If any of the other

points have been changed while these points

were inhibited, the inhibited points will change

to plot a smooth curve. If you want to keep

this from happening, press the Select key to

display the positions 1 and 3, then press the (+)

or (-) key to activate each point.

6. To set curves for STUNT mode, press the Select to

highlight the NORM function, then press the (+) or

(-) key to select the STUNT function, Repeat Steps 4

and 5 to complete the procedure.

7. To set the curves for the Throttle Hold mode “H“,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX12 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info