Bedienungsanleitung Graupner MX12 (Seite 8 von 48) (Englisch)

30127

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

8 Charging the transmitter battery

Charging the transmitter battery

The rechargeable transmitter battery can be charged

via the charge socket fitted to the side of the case.

The transmitter must be switched „OFF“ for the whole

period of the charge process. Never switch on the

transmitter when it is still connected to the charger;

even a very brief interruption in the charge process

can cause the charge voltage to rise to the point where

the transmitter is immediately damaged by the excess

voltage. Alternatively the interruption may trigger a new

charge cycle, which means that the battery will possibly

be severely overcharged.

For this reason check carefully that all connectors

are secure, and making really good contact. Inter-

ruptions due to an intermittent contact, no matter

how brief, inevitably cause the charger to malfunc-

tion.

Polarity of the mx-12 charge socket

Commercially available battery charge leads produced

by other manufacturers are often made up with the op-

posite polarity. For this reason use genuine GRAUPNER

charge leads exclusively.

Charge current

To avoid damage to the transmitter the maximum charge

current should not exceed 500 mA (0.5 A) with the char-

ge circuit fuse out of circuit (not fitted); with the charge

circuit fuse in place: max. 1.5 A.

Notes on recharging transmitter batteries using an

automatic charger

· Observe the recommendations provided by the

charger manufacturer and the battery manufactu-

rer at all times.

· Carry out a series of test charges to ensure that

the automatic charge termination circuit works

correctly with your battery. This applies in parti-

cular if you are using an automatic charger desig-

ned for NiCd batteries to recharge the standard

NiMH battery. You may need to adjust the Delta-

Peak trigger voltage, if your charger provides this

option.

· The charge current must be set using the

charger’s „manual charge current select“ facility,

to ensure that the maximum charge current never

exceeds 1.5 A. Never allow the charger to set the

charge current automatically.

· Do not discharge the battery or carry out a

battery maintenance program via the integral

charge socket. The charge socket is not suitable

for this application.

· If you intend to charge the transmitter battery at

a current higher than 1.5 A, the battery must be

removed beforehand, otherwise the transmitter

could be damaged through overheating.

Standard chargers

Order-No. 6422 Minilader 2

Order-No. 6427 Multilader 3

Order-No. 6426 Multilader 6E*

Order-No. 6428 Turbomat 6 Plus*

Order-No. 6429 Turbomat 7 Plus*

Automatic chargers with special NiMH charge

programs

Order-No. 6419 Ultramat 5*, **

Order-No. 6410 Ultramat 10*

Order-No. 6412 Ultramat 12*, **

Order-No. 6417 Ultramat 25*, **

Order-No. 6416 Ultra Duo Plus 30*, **

* To recharge the mx-12 system you will also need the transmitter

charge lead, Order No. 3022, and the receiver battery charge lead,

Order No. 3021.

** 12 V power source required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX12 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info