Bedienungsanleitung Graupner MX12 (Seite 22 von 48) (Englisch)

30127

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Go to Throttle cut

Go to Ele Flp

Mx menu

Change selection

Change value/Select

switch

Reset selection to

Default (Adjust to

0% or ALWAYS ON)

Accessing the Aileron to Rudder Mixing Function

1. Place the transmitter power switch in the ON positi-

on.

2. Access the Function mode. To do so, press the

Down and Select keys simultaneously. Press

either the Up or Down key until AILRUD MIX

appears in the center portion of your LCD.

3. Press the (+) or (-) key to increase or decrease the

amount of rudder to be mixed with aileron. If you

want to reverse the Rudder Mix direction, press the

Clear key, bringing the mixing value to the factory

default (0%), and increase the value using the oppo-

site key (+) ir (-) from the key originally selected.

4. Press the Select key to access the switch assign-

ment function.

5. Press the (+) or (-) key to select the desired switch/

function to activate the Aileron-to-Rudder Mixing

function.

6. Access the ELEFLP MX mixing function by pres-

sing the Down key.

7. Access the THRO CUT function by pressing the Up

key.

8. Exit the AILRUD MIX function by pressing the

Down and Select keys simultaneously.

22 Function mode AIRPLANE

Function mode AIRPLANE

Throttle Cut switch; Flap System

Throttle Cut switch

This function assigns the Throttle Cut switch to the push

button located on upper right front of the transmitter.

The Throttle Cut function is designed to return the

throttle trim to the lowest position instantly and keep this

position while the button is pressed. This feature is used

to “cut“ or stop the engine without changing the position

of digital throttle trim.

Throttle cut operating position

(-32~-128)

Go to Flap System

Go to AilRud

Mix menu

Change value

Set function to

Inhibit

Accessing the Throttle Cut Function

1. Place the transmitter power switch on the ON positi-

on.

2. Access the Function mode. To do so, press the

Down and Select keys simultaneously. Press

either the Up or Down key, until THRO CUT

appears in the upper portion of the LCD screen.

3. Use the (+) and (-) keys to change the value of the

Throttle cut function.

Note: Pressing the Clear key will Inhibit the Throttle

Cut, turning it off until it has been reactivated.

4. Access the FLAP SYSTEM mixing function by pres-

sing the Down key.

5. Access the AILRUD MIX function by pressing the

Up key.

6. Exit the THRO CUT function by pressing the Down

and Select keys simultaneously.

Flap System

The Flap System function provides elevator compensa-

tion to counteract any pitch tendencies when flaps are

deployed.

SW Position

LANDING: (Flap SW forward side)

Elevator Offset value

Travel value (DN200~0~UP200)

Flap operating value Travel value

(DN125%~0%~UP125%)

Change value

Reset to selection

to Default

Go to Differential

Go to Throttle Cut

Change selection

Accessing the Flap System Function

1. Place the transmitter switch in the ON position.

2. Press the Down and Select keys simultanously to

enter the Function mode.

3. Press either the Up or Down key until FLAP SYS-

TEM appears in the top of the LCD.

4. Press the Select key to select the desired channels

to be adjusted.

5. Use the (+) or (-) keys to set the desired landing

mode surface positions.

6. Access the THRO CUT mixing function by pressing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX12 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info