Bedienungsanleitung Graupner MX12 (Seite 42 von 48) (Englisch)

30127

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

System Mode

sing function to reverse the travel direction.

Note: Each servo‘s direction is adjusted individually

through the Servo Reversing function. For more

information, refer to the Servo Reversing sec-

tion in this manual.

7. Once the servos direction has been set, adjust their

travel direction, travel volume, dual-rates, sub-trim

and aileron differential.

Note: The applicable channel‘s left or right, up or

down travel adjustments can be made individu-

ally. Refer to the Travel Adjust section in this

manual for more information.

8. Relative to the note above, each servo‘s travel

volume is automatically reduced to 75% of the

operating range. This is to ensure that the servo

does not operate beyond its capabilities. Failure to

observe extreme caution when adjusting the value

for the elevon servos may result in damage to the

servos by over traveling.

Note: Fine adjustments of the elevons should be

made in the Dual-Rate function. For more infor-

mation, refer to the Dual-Rate section in this

manual. You can also adjust the neutral point of

your elevon servos individually using the Sub-

Trim function as described in the Sub-Trim

section of this manual. Differential is offered for

the elevon function of your mx-12. For more

information, refer to the Differential Aileron

Mixing section of this manual.

9. Press the Down key to access the SWITCH SEL

function.

10. Press the Up key to access the MODEL SEL func-

tion.

11. To exit the WING TYPE function, press the Down

and Select keys simultaneously.

servos. However, there is not an elevator present.

Instead, an elevator stick input causes the two wing

servos to function in conjunction with one another to

change the pitch movement of the aircraft. Also, when

an aileron control is given the two wing servos move in

opposition to one another to function as ailerons.

Connect left servo to the

aileron port of the receiver

Connect right servo to the

elevator port of the receiver

Accessing and Ultilizing the Elevon Type Selection

1. While the Down and Select keys are pressed,

move the power switch to the ON position to access

the System mode.

2. Press either the Up or Down key until WING TYPE

appears on the LCD.

3. Press the Select key to select the Elevon functions.

4. Press either the (+) or (-) key to turn on the Elevon

Wing Type function.

Note: The Elevon function requires one servo for each

elevon, i.e. a separate servo for each wing half.

5. Plug the left elevon servo to the aileron (AILE) of

your GRAUPNER receiver. Connect the right elevon

servo into the elevator (ELEV) port of your receiver.

6. Check to make sure the servos move in the proper

direction. When an input is given from the elevator

stick, they should move in unison to achieve the

proper up/down elevator command. If your servos do

not move as described above, use the Servo Rever-

direction.

Note: Each servo‘s travel direction is adjusted indivi-

dually through the Servo Reversing function.

Once the servos achieve their proper travel direction,

adjust their travel amount, dual rates, sub-trim and

aileron differential.

Note: The applicable channel‘s left or right travel

adjustment may be made individually by acces-

sing the Travel Adjust function. Refer to the

Travel Adjust section of this manual for more

information. The fine adjustments of your aileron

controls should be made in the Dual-Rate func-

tion. Refer to the Dual-Rate section for informa-

tion on how to do so. You can also adjust the

neutral point of your aileron servos individually

through the use of the Sub-Trim function. Refer

to the Sub-Trim section of this manual for more

information.

6. The flap lever located on the left face of the transmit-

ter controls the aileron movements as flaps. To turn

off flaps go to the Flap System function on page 39

and reduce the flap value to 0%.

Note: Differential is offered for the Flaperon function of

your mx-12. For more information, please refer

to the Differential section of this manual.

7. Press the Down key to access the SWITCH SEL

function.

8. Press the Up key to access the MODEL SEL func-

tion.

9. Exit the WING TYPE function by pressing the

Down and Select keys imultaneously.

Elevon Type Selection

Elevon Wing Mixing is available as an option with your

mx-12. This style of aircraft also employs two wing

42 System Mode

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner MX12 Seite 42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Graupner MX12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info