Bedienungsanleitung Graupner POLARON EX-1400 - GR-S2018 (Seite 23 von 29) (Englisch)

637253

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

English

INNOVATION & TECHNOLOGIE

44 45

3. Display “Date & time“

This screen is used to set the date and time *, and possibly two alarms.

After tapping the value to change, this can be changed with the INC / DEC but-

tons located at the bottom of the display. Tapping again the value eld stores

the changed value and deactivates the input eld again.

An alarm can be activated by switching from OFF to ON and vice versa ena-

bled. The set time triggered alarm is stopped by tapping the screen, but re-

mains active as long as it is not disabled in this menu.

* The abbreviations “AM” (ante meridian = before noon) and “PM” (post meridiem = after noon) derived from Latin

and are used among others in the English language.

4. Display “Username and Options“

Parameter Short description

Username Tap this line, the display opens to enter a user name.

Proceed as described under “Entering a battery name “ on

page 18.

Options This menu is disabled at the time of the revision of this

manual, but should be activated with the next update.

Menu STORAGE

In the menu “PROFILE” you have stored the data of your batteries and this adds to the menu

“CHARGE” and “DISCHARGE” to the charge or discharge parameters. The charger charges or

discharges your lithium battery to its storable state based on these parameters.

The default value in the line “storage voltage” gives a battery about 60% of its capacity.

The selected memory location is displayed at the top of the screen and, once this eld is highlight-

ed in blue by touching with a nger or the supplied pen, it can be selected individually. Similarly

proceed with the other options elds of this display.

If you set [N-STORE] the CC / CV is applied and if you set [Q-STORE], then FAST-charge method

is applied.

Parameter* Short description

Mode NORMAL or FAST

Cell count Specication of cell voltage for the storage mode

Charge current Charge current value

Discharge cur-

rent

Discharge current value

Starting the process is like any other, possible steps as described under

“Charge” on page 18, “Discharge” on page 24 or “Cycle” on page 28.

Press and hold the push button placed under the display and turn on the

charger. After a short time, the display will appear as shown on the left.

Display “1. Factory reset“

Tapping the “1. Factory reset “ button, as shown above, launches a reset of the

Graupner polaron EX-1400 charger.

ATTENTION!

The factory reset starts after pressing the button WITHOUT

FEEDBACK!!! All data and settings will be cleared and the de-

vice will be reset to factory settings!!!

During the battery charger reset to the factory settings it will be shown alter-

nately in red and blue the script, “initialize data ...”, as shown at left.

After successfully reset the charger restarts automatically.

Display “2. Display calibration“

Tapping the “2. Display Calibration“ button, as shown above, opens the display as shown below. In

this one you will be asked three times to tap the center of the red cross.

Afterwards the cross changes twice its position and promptly you have to triple tap on it, see mid-

dle and right of the three images below:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner POLARON EX-1400 - GR-S2018 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info