Bedienungsanleitung Graupner ULTRA TRIO PLUS 16 - 6469 (Seite 29 von 107) (Deutsch, Englisch, Französisch, Italienisch)

637232

Zoom out

Zoom in

Vorherige Seite

1/107

Nächste Seite

2. Warnings and safety notes

 This product isn‘t designed for use by children under the age of 14, it isn‘t a toy!

 Protect the charger from dust, damp, rain, heat (e.g. direct sunshine) and vibration. It should only be operated

in dry indoor conditions.

 The case slots serve to cool the charger, and must not be covered or enclosed; set up the charger with

space round it, so that cooling air can circulate unhindered.

The charger is designed to be powered by a 12 V DC car battery or power supply or 100~240V AC main

socket only. It is not permissible to modify the charger in any way. Never use both inputs AC and DC at the

same time!

 The charger and the battery to be charged should be set up on a heat-resistant, non-inﬂ ammable and

non-conductive surface before use. Never place the charger directly on a car seat, carpet or similar. Keep

all inﬂ ammable and volatile materials well away from the charging area. Provide good ventilation. Defective

batteries can explode or burn!

 Connect the charger 12DC input directly to the car battery using the original cables and connectors sup-

plied. The car’s engine must be stopped all the time the charger is connected to the car’s battery. Do not

recharge the car battery at any time when the charger is connected to it.

 The charge output sockets and connecting leads must not be modiﬁ ed, and must not be inter-connected in

any way. There is a danger of short-circuit between the charge outputs and the vehicle’s bodywork when the

charger is connected to the car battery. The charge leads and connecting leads must not be coiled up when

the charger is in use. Avoid short-circuiting the charge output or the model battery with the car bodywork.

For this reason the charger must never be placed directly on the vehicle’s bodywork.

 Never leave the charger running or connected to the car battery unsupervised.

 Only one battery may be connected to the unit for charging at any one time.

 The following types of battery must not be connected to the charger:

- Ni-Cd / Ni-MH batteries consisting of more than 14 cells, Lithium-Ion / Li-Mn / Lithium-Polymer / LiFePO

(LiFe) batteries of more than 6 cells, or lead-acid batteries with a nominal voltage of more than 12V.

- Batteries which require a different charge method from Ni-Cd, Ni-MH, Lithium or lead-acid types.

- Faulty or damaged cells or batteries.

- Batteries consisting of parallel-wired cells, or cells of different types.

- Batteries consisting of old and new cells, or cells of different makes.

- Non-rechargeable batteries (dry cells). Caution: explosion hazard!

- Batteries which are not expressly stated by the manufacturer to be suitable for the currents which this unit

delivers during the charge process.

- Packs which are already fully charged or hot, or only partially discharged.

- Batteries or cells ﬁ tted with an integral charge circuit or charge termination circuit.

- Batteries installed in a device, or which are electrically connected to other components.

 To avoid short-circuits between the banana plugs ﬁ tted to the charge leads, please always connect the

charge leads to the charger ﬁ rst, and only then to the battery to be charged. Reverse the sequence when

disconnecting.

 As a basic rule always check that the charge quantity is approximately the same as you expected after the

charger has indicated that the pack is fully charged. This is a simple method of detecting a problem reliably

and in good time, should the charge process be terminated prematurely for any reason. The likelihood of

premature termination varies according to many factors, but is at its highest with deep-discharged packs,

low cell counts and particular cell types which are known to cause problems.

 We recommend that you carry out a series of test charges to satisfy yourself that the automatic termination

circuit is working perfectly. This applies in particular when you are charging packs consisting of a small

number of cells. If the cells feature has a poorly deﬁ ned voltage peak, the charger may fail to detect the fully

charged state.

 Before charging please check: have you selected the appropriate charge program for the battery? Have

you set the correct charge or discharge current? Have you set the important cut-off voltage when charging

Ni-Cd and Ni-MH packs? Are all connections ﬁ rm, or is there an intermittent contact at any point in the

circuit? Please bear in mind that it can be dangerous to fast-charge batteries. For example, if there is a

brief interruption due to an intermittent contact, the result is inevitably a malfunction such as a restart of the

charge process, which would result in the pack being massively overcharged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner ULTRA TRIO PLUS 16 - 6469 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info