Bedienungsanleitung Graupner Ultramat 18 - 6470 (Seite 25 von 92) (Deutsch, Englisch, Französisch)

637245

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

2. Warnings and safety notes

z This product isn‘t designed for use by children under the age of 14, it isn‘t a toy!

z Protect the charger from dust, damp, rain, heat (e.g. direct sunshine) and vibration. It should only be

operated in dry indoor conditions.

z The case slots serve to cool the charger, and must not be covered or enclosed; set up the charger

with space round it, so that cooling air can circulate unhindered.

z The charger is designed to be powered by a 12 V DC car battery or power supply or 100~240V AC

main socket only. It is not permissible to modify the charger in any way. Never use both inputs AC and

DC at the same time!

z The charger and the battery to be charged should be set up on a heat-resistant, non-inflammable

and non-conductive surface before use. Never place the charger directly on a car seat, carpet or

similar. Keep all inflammable and volatile materials well away from the charging area. Provide good

ventilation. Defective batteries can explode or burn!

z Connect the charger 12DC input directly to the car battery using the original cables and connectors

supplied.

The car’s engine must be stopped all the time the ULTRAMAT 18 is connected to the car’s

battery.

Do not recharge the car battery at any time when the ULTRAMAT 18 is connected to it.

z The charge output sockets and connecting leads must not be modified, and must not be inter-

connected in any way. There is a danger of short-circuit between the charge outputs and the vehicle’s

bodywork when the charger is connected to the car battery. The charge leads and connecting leads

must not be coiled up when the charger is in use. Avoid short-circuiting the charge output or the

model battery with the car bodywork. For this reason the charger must never be placed directly on the

vehicle’s bodywork.

z Never leave the charger running or connected to the car battery unsupervised.

z Only one battery may be connected to the unit for charging at any one time.

z The following types of battery must not be connected to the charger:

- Ni-Cd / Ni-MH batteries consisting of more than 30 cells, Lithium-Ion / Li-Mn / Lithium-Polymer /

LiFePO

(LiFe) batteries of more than 12 cells, or lead-acid batteries with a nominal voltage of more

than 24V.

- Batteries which require a different charge method from Ni-Cd, Ni-MH, Lithium or lead-acid types.

- Faulty or damaged cells or batteries.

- Batteries consisting of parallel-wired cells, or cells of different types.

- Batteries consisting of old and new cells, or cells of different makes.

- Non-rechargeable batteries (dry cells). Caution: explosion hazard!

- Batteries which are not expressly stated by the manufacturer to be suitable for the currents which

this unit delivers during the charge process.

- Packs which are already fully charged or hot, or only partially discharged.

- Batteries or cells fitted with an integral charge circuit or charge termination circuit.

- Batteries installed in a device, or which are electrically connected to other components.

z To avoid short-circuits between the banana plugs fitted to the charge leads, please always connect

the charge leads to the charger first, and only then to the battery to be charged. Reverse the sequence

when disconnecting.

z As a basic rule always check that the charge quantity is approximately the same as you expected after

the charger has indicated that the pack is fully charged. This is a simple method of detecting a problem

reliably and in good time, should the charge process be terminated prematurely for any reason. The

likelihood of premature termination varies according to many factors, but is at its highest with deep-

discharged packs, low cell counts and particular cell types which are known to cause problems.

z We recommend that you carry out a series of test charges to satisfy yourself that the automatic

termination circuit is working perfectly. This applies in particular when you are charging packs consisting

of a small number of cells. If the cells feature has a poorly defined voltage peak, the charger may fail

to detect the fully charged state.

z Before charging please check: have you selected the appropriate charge program for the battery?

Have you set the correct charge or discharge current? Have you set the important cut-off voltage

when charging Ni-Cd and Ni-MH packs? Are all connections firm, or is there an intermittent contact at

any point in the circuit? Please bear in mind that it can be dangerous to fast-charge batteries. For

example, if there is a brief interruption due to an intermittent contact, the result is inevitably a

malfunction such as a restart of the charge process, which would result in the pack being massively

overcharged.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Graupner Ultramat 18 - 6470 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info