Bedienungsanleitung Greenlee CLM-1000E (Seite 6 von 36) (Deutsch, Französisch, Spanisch)

627691

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Operation

Electric shock hazard:

Do not connect the unit to live voltage.

Contact with live circuits could result

in severe injury or death.

Calibration Procedure

Each time the meter is turned ON, it should be calibrated

before use.

1. Refer to “Typical Measurements” for calibration setup

diagram.

2. Ensure the calibration bar and Kelvin clips jaws are

clean.

3. Move rotary switch from the OFF position to Ω.

4. Ensure that both leads for the red set of Kelvin clips

are plugged into the red terminals on the meter.

Ensure that both leads for the black set of Kelvin clips

are pluggged into the black terminals on the meter.

5. Place each Kelvin clip on the calibration bar. Move the

clips as close together as possible.

6. Press the CAL button. Dashes appear on the LCD.

Next “MEM” and “donE” appear on the LCD. Then

“RES” on the LCD indicates the meter is back in

resistance mode. If “FAIL” appears on the LCD and the

buzzer sounds, there was an issue with the calibration

process. Turn meter OFF and return to step 1 of this

procedure.

7. After successful completion of the calibration process,

the meter is ready for normal operation.

Operating Procedure

1. If the unit does not function as expected on a known

functioning conﬁguration, replace the batteries.

If the unit still does not function as expected, call

Greenlee for technical assistance at 800-435-0786.

2. Refer to “Typical Measurements” for speciﬁc mea-

surement instructions.

3. The meter does not compensate for manufacturing

tolerances of various cable manufacturers.

4. Before making a measurement, ensure the following:

• Cable conductors have been cleaned with

abrasive material to remove oxide layer and other

contaminants.

• Kelvin clip jaws are clean.

• Both the cable and meter are at the same

temperature.

• Cable conductor material must be either aluminum

or copper.

5. To measure odd cable sizes:

• AWG (5, 7, 9, 11 AWG, etc.) (CLM-1000): When

measuring odd numbered cable sizes, set the rotary

switch to the next smaller size, and multiply the

reading by 1.261.

For example, to measure a 9 AWG length of cable,

set the rotary switch to 10 AWG. Then multiply the

reading by 1.261 to get the length.

• kcmil (CLM-1000): When measuring odd

numbered cable sizes, set the rotary switch to

1000kcmil. Divide kcmil size of cable being mea-

sured by 1000, and then multiply this number by the

meter’s length reading.

For example, 477 kcmil cable is being measured.

The multiplier becomes 477/1000 = 0.477. Take

the value shown with the rotary switch in the 1000

kcmil position and multiply it by 0.477 to get the

length.

• mm

(CLM-1000E): When measuring odd

numbered cable sizes, set the rotary switch to

500mm

. Divide mm

size of cable being mea-

sured by 500, and then multiply this number by the

meter’s length reading.

For example, 289 mm

cable is being measured.

The multiplier becomes 289/500 = 0.596. Take the

value shown with the rotary switch in the 500 mm

position and multiply it by 0.596 to get the length.

Programming Procedure

1. Calibrate meter according to “Calibration Procedure.”

2. Obtain known length of cable between 30 ft and

320ft (9 m and 97.5 m) long. Cable must be alumi-

num or copper.

3. Set rotary switch to desired location. Programmable

location appears on the LCD. If the location has

already been programmed, “OL” appears on the LCD.

If it has not, “no” appears.

Note: Data in a programmed location can be deleted.

With Kelvin clips removed from cable and rotary

switch turned to location to delete, press MEM button.

4. Press CAL button.

5. Enter the known length of cable in feet or meters.

Useqp arrows.

6. Select “Cu” or “Al”.

7. Connect Kelvin clips to the conductor on each end of

the cable.

8. Press MEM button. “MEM” and dashes appear on the

LCD. After approximately 1 second, “donE” appears

on the LCD if programming was successful. If “FAIL”

appears, check connections and repeat procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Greenlee CLM-1000E Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info