Bedienungsanleitung Greenworks G24ST - 2101207 (Seite 5 von 162) (Alle Sprachen)

708335

Zoom out

Zoom in

Vorherige Seite

1/162

Nächste Seite

English (original instructions)

DE ES IT FR PT NL RU FI SV NO DA PL CS SK SV HR HU RO BG EL AR TR HE LT LV ET

WARNING

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

WARNING

To avoid serious personal injury, always remove the

battery pack from the tool when cleaning or performing

any maintenance.

GENERAL MAINTENANCE

Before each use, inspect the entire product for damaged,

missing, or loose parts such as screws, nuts, bolts, caps,

etc. Tighten securely all fasteners and caps and do not

operate this product until all missing or damaged parts are

replaced.

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use.

Use clean cloths to remove dirt, dust, oil, grease, etc.

WARNING

Do not at any time let brake uids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

Only the parts shown on the parts list are intended to

be repaired or replaced by the customer. All other parts

should be replaced at an Authorised Service Centre.

SPOOL REPLACEMENT See Figure 12.

Use original manufacturer’s replacement cutting line for

best performance.

 Remove the battery pack.

 Push in tabs (C) on side of spool cover (A).

 Pull spool cover up to remove.

 Remove the old spool.

 To install the new spool (B), make sure the cutting line

is captured in the slot on the new spool (F). Make sure

the end of the cutting line is extended approximately

15cm beyond the slot.

 Install the new spool so that the cutting line and slot

align with the eyelet (E) in the cutting head (G). Thread

the cutting line into the eyelet.

 Pull the cutting line extending from the cutting head so

the cutting line releases from the slot in the spool.

 Reinstall the spool cover by depressing tabs into slots

(D) and pushing down until spool cover clicks into

place.

CUTTING LINE REPLACEMENT See Figure 13.

 Remove the battery pack.

 Remove the spool from the cutting head.

NOTE: Remove any old cutting line remaining on the

spool.

 Cut a piece of cutting line approximately 3m long.

 Insert the cutting line into the anchor hole (B) in the

upper part of the spool. Wind the cutting line around

the upper part of the spool clockwise, as shown by the

arrows on the spool. Place cutting line in the slot (C)

on upper spool flange, leaving about 15 cm. extended

beyond the slot. Do not overfill. After winding the cutting

line, there should be at least 0.635 cm between the

wound cutting line and the outside edge of the spool.

 Replace the spool (A), and the spool cover. Refer to

spool replacement earlier in this manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Greenworks G24ST - 2101207 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info