Bedienungsanleitung Greenworks GD40CS - 20077 (Seite 22 von 256) (Alle Sprachen)

708317

Zoom out

Zoom in

Vorherige Seite

1/256

Nächste Seite

English

FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG

under tension should be cut from the bottom up, to avoid

binding the chain saw.

BUCKING A LOG

See ﬁ gure 12 - 15

Bucking is cutting a log into lengths. It is important to

make sure your footing is ﬁ rm and your weight is evenly

distributed on both feet. When possible, the log should be

raised and supported by the use of limbs, logs or chocks.

Follow the simple direction for easy cutting:

1. When the log is supported along the entire length, it is

cut from the top (over buck).

2. When the log is supported on one end, cut 1/3 of the

diameter from the underside (under buck). Then make

the ﬁ nished cut by over bucking to meet the ﬁ rst cut.

3. When the log is supported on both ends, cut 1/3 of

that diameter from the top (over buck). Then make the

ﬁ nished cut by under bucking the lower 2/3 to meet

the ﬁ rst cut.

4. When bucking on a slope, always stand on the up-

hill side of the log. When cutting through, to maintain

complete control, release the cutting pressure near the

end of the cut without relaxing your grip on the chain

saw handles.

Do not let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving from

tree to tree.

MAINTENANCE

WARNING

Always remove the battery pack from the machine

before checking the chain tension or making

adjustments to the chain. Wear protective gloves while

touching the chain, bar or areas around the chain.

ADJUSTING THE CHAIN TENSION

See ﬁ gure 2

Un-tighten the sprocket cover tighten knob (item 15)

slightly by turning it counterclockwise.

To increase the chain tension, turn the chain tensioner

adjustment knob (item 13) clockwise and check the

chain tension frequently. To reduce the chain tension,

turn the chain tensioner adjustment knob (item

13) counterclockwise and check the chain tension

frequently.

The chain tension is correct when the gap between the

cutter in the chain and the bar is between 3mm-4mm.

Pull the chain in the middle of the lower side of the

bar downwards (away from the bar) and measure the

distance between the bar and the chain cutters.

Tighten the sprocket cover tighten knob (item 15) by

turning it clockwise.

REPLACING THE BAR AND CHAIN

See Figure 2, 3, 5, 7

Put the saw down on a flat and even surface to make

adjustments to the chain.

Make sure that you have the correct replacement

bar and chain as advised earlier in he specification

section of this manual.

Unscrew the sprocket cover tighten knob (item 15) by

turning it counterclockwise until the sprocket cover

(item 14) comes loose.

Remove the sprocket cover. Remove the bar and saw

chain from unit.

To replace the bar with the new one, unscrew the nut

of the safety ip, mount the safety tip on to the new bar

and tighten the nut.

Put the new chain in the correct direction as shown in

figure 7 onto the bar and make sure that the drive links

are aligned in the bar groove (figure 5).

Attach the bar to the chain saw and loop the chain

around the drive sprocket as shown in figure 3.

Replace the sprocket cover (item 14), tighten sprocket

cover and ighten knob (item 15).

Follow the steps the section “ADJUSTING THE CHAIN

TENSION” earlier in this manual.

ADDING CHAIN & BAR LUBRICANT

Unscrew and remove the cap (item 6) from the oil tank.

Pour the oil into the oil tank and monitor he oil level

gauge (item 7). Ensure that no dirt enters the oil tank

while filling the oil in.

Put the oil cap back on and tighten it up.

One full oil tank will enable you to use the saw for 20-

40 min.

TRANSPORTING THE CHAIN SAW

Before transporting the chain saw, always remove the

battery pack from he chain saw and slide the chain cover

over the bar and chain. If several cuts are to be performed

with he chain saw, the saw must be switch off between

cuts.

GUIDE BAR COVER

See ﬁ gure 1

The chain cover must be clipped onto the chain and bar

as soon as the sawing work has been completed and

whenever the machine has to be transported.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Greenworks GD40CS - 20077 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info