Bedienungsanleitung Greenworks GD80CS50 - 2000507 (Seite 22 von 260) (Alle Sprachen)

708327

Zoom out

Zoom in

Vorherige Seite

1/260

Nächste Seite

English

FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG

under tension should be cut from the bottom up, to avoid

binding the chain saw.

BUCKING A LOG

See figure 12 - 15

Bucking is cutting a log into lengths. It is important to

make sure your footing is firm and your weight is evenly

distributed on both feet. When possible, the log should be

raised and supported by the use of limbs, logs or chocks.

Follow the simple direction for easy cutting:

1. When the log is supported along the entire length, it is

cut from the top (over buck).

2. When the log is supported on one end, cut 1/3 of the

diameter from the underside (under buck). Then make

the finished cut by over bucking to meet the first cut.

3. When the log is supported on both ends, cut 1/3 of

that diameter from the top (over buck). Then make the

finished cut by under bucking the lower 2/3 to meet

the first cut.

4. When bucking on a slope, always stand on the up-

hill side of the log. When cutting through, to maintain

complete control, release the cutting pressure near the

end of the cut without relaxing your grip on the chain

saw handles.

Do not let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving from

tree to tree.

MAINTENANCE

WARNING

Always remove the battery pack from the machine

before checking the chain tension or making

adjustments to the chain. Wear protective gloves while

touching the chain, bar or areas around the chain.

ADJUSTING THE CHAIN TENSION

See figure 2 and figure 7

ADDING CHAIN & BAR LUBRICANT

Unscrew and remove the cap (item 6) from the oil tank.

Pour the oil into the oil tank and monitor the oil level

gauge (item 7). Ensure that no dirt enters the oil tank

while filling the oil in.

Put the oil cap back on and tighten it up.

One full oil tank will enable you to use the saw for 20-

40 min

TRANSPORTING THE CHAIN SAW

Before transporting the chain saw, always remove the

battery pack from the chain saw and slide the chain cover

over the bar and chain. If several cuts are to be performed

with the chain saw, the saw must be switch off between

cuts.

GUIDE BAR COVER

See figure

The chain cover (item 1) must be clipped onto the chain

and bar as soon as the sawing work has been completed

and whenever the machine has to be transported.

RCS36-23lgs manual.indd 19 2010/12/30 3:14

Loosen the chain cover lock nuts (item 15) with the

supplied wrench. The chain cover lock nuts do not

have to be completely removed in order to adjust the

chain tension.

Rotate the chain adjustment screw(item 13) clockwise

to increase the chain tension and rotate

counterclockwise to decrease the chain tension.

Once the chain is at the desired tension, tighten the

chain cover lock nuts(item 15).



REPLACING THE BAR AND CHAIN

See Figure 3-7



Remove the battery from the chain saw.

Remove the supplied wrench(item 11) from the rear handle

(item 12).

Remove the two chain cover lock nuts (item 15) from chain

cover by rotating them counterclockwise with the wrench.

Remove the chain cover(item 14) from the mounting surface.

The bar and chain can now be removed by lifting it away from

the main body of the saw and releasing the chain from the

sprocket.

Remove the old chain from the bar.

Lay out the new saw chain in a loop and straighten any kinks.

The cutters should face in the direction of chain rotation. If they

face backwards, turn the loop over.

Place the chain drive links into the bar groove.

Position the chain so there is a loop at the back of the bar.

Hold the chain in position on the bar and place the loop around

the sprocket.

Fit the bar flush against the mounting surface so that the bar

studs are in the long slot of the bar. Ensure that the chain is

over the sprocket.

Replace the chain cover.

Remove all slack from the chain by turning the chain adjustment

screw(item 13) clockwise until the chain seats snugly against

the bar with the drive links in the bar groove(item 20).

Lift the tip of the guide bar up to check for sag.

Release the tip of the guide bar and turn the chain adjustment

screw 1/2 turn clockwise. Repeat this process until sag does

not exist.

Hold the tip of the guide bar up and tighten the chain cover

lock nuts by turning them with the wrench. The chain is correctly

tensioned when there is no sag on the underside of the guide bar,

the chain is snug, but it can be turned by hand without binding.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Greenworks GD80CS50 - 2000507 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info