Bedienungsanleitung Grizzly AHS 1845 T Lion (Seite 32 von 145) (Deutsch, Englisch, Holländisch, Französisch, Spanisch, Polnisch)

626729

Zoom out

Zoom in

Vorherige Seite

1/145

Nächste Seite

Always hold the equipment rmly

in both hands, with one hand on the

rear handle and the other on the front

handle. Thumbs and ngers must be

rmly around the handles.

Observe the specied working an-

gle (60°±10°), in order to guarantee

safe working.

• Switch off the equipment immedi-

ately in the event that the blades are

blocked by solid objects, pull out the

power plug then remove the object.

• Always work away from the mains pow-

er outlet. Set the cutting direction before

starting work. Ensure that the power

cable is kept well away from the work-

ing area. Never lay the cable over the

hedge, where it could easily be caught

up in the trimmer blades.

• Do not use the unit if the blades are

blunt or worn. This will overstress the

motor and gearbox of the machine.

• Avoid overstraining the equipment dur-

ing work.

• Change position regularly while operat-

ing the device. Prolonged use of the

device can lead to blood circulation

disorders in the hands caused by vi-

bration. You can however extend your

machine use time by wearing appropri-

ate safety gloves or by taking regular

breaks. Please note that a personal

disposition to poor blood circulation,

low outside temperatures, or strong

grip forces while working may reduce

your work capabilities.

Cutting Techniques

• Cut thick branches beforehand using a

branch clippers.

• The double-sided cutter bar enables

cutting in both directions or, with a

swinging action, from one side to the

other.

• In case of vertical cutting, move the

hedge trimmer uniformly forward or up

and down in an arc movement.

• In case of horizontal cutting, move the

hedge trimmer in a sickle-shaped move-

ment to the edge of the hedge, so that

cut branches fall to the ground.

• In order to achieve long straight lines,

the placing of tensioned guiding cords

is recommended.

Cutting Shaped Hedges:

It is recommended that hedges be

cut in a trapezoidal shape, in order

to prevent stripping off of the lower

branches. This corresponds to the

natural plant growth and allows the

hedge to thrive optimally. During cut-

ting, only the new annual growths

are reduced and thus a dense

branching and a good screen will

develop.

1. Cut the sides of a hedge rst. To do this,

move the hedge trimmer in the direction

of growth from bottom to top. If you cut

down from the top, the thinner branches

will move out, which may result in some

areas having sparse growth or holes.

2. Cut the top edge, according to taste, in a

at shape, roof shape or rounded shape

3. Trim young plants to the required shape.

The main growth should remain undam-

aged until the hedge has reached the

planned height. All other shoots are

lopped off to half size.

Care of Free-Growing Hedges:

Free-growing hedges are not shaped when

cut, although they must be regularly main-

tained so the hedge does not become too

high.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grizzly AHS 1845 T Lion Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info