Bedienungsanleitung Grohe 24016 Atrio (Seite 4 von 8) (Deutsch, Englisch, Französisch, Spanisch)

759565

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

English

Application

Operation is possible in conjunction with:

- Pressurized storage heaters

- Thermally controlled instantaneous heaters

- Hydraulically controlled instantaneous heaters

Operation with low-pressure storage heaters (displacement water

heaters) is not possible.

Specifications

•Max. flow 13 L/min or 3.4 gpm/45 psi

•Flow pressure

- min. 7.25 psi

- recommended 14.5 - 72.5 psi

- greater than 72.5 psi, fit with pressure reducing valves

•Max. operating pressure 145 psi

•Test pressure 232 psi

•Temperature

- max. (hot water inlet) 176 °F

• Water connection cold - Right hand

hot - Left hand

Notes

•Installation of backflow protection must comply

with local codes and regulations.

•Major pressure differences between cold and hot water supply

should be avoided.

Installation

See dimensional drawing on fold-out page I.

Flush pipes thoroughly!

Side valves

•Valve marked with "L" (left close) on the top edge of the

cartridge (A) with blue tape should be mounted on the right (cold

water) side, see fold-out page II, fig. [1].

•Valve marked with "R" (right close) on the top edge of the

cartridge (A) with red tape should be mounted on the left (hot

water) side.

1. Screw the mounting set (B) to the bottom of the thread of the

side valve (C), see fig. [1].

Make sure that the rubber washer (B1) is on the top of the fiber

washer (B2).

2. Insert the side valve (C) through the basin hole from below.

3. Place the escutcheon O-ring (D1) on the basin and screw down

the escutcheon (D) until it stops.

4. Screw the cap (E) down to the escutcheon (D).

5. Secure snap insert (F) with screw (G) to the stem of the ceramic

cartridge (A).

6. Tighten the mounting set (B) from below to secure the valve.

Vacuum breaker

1. Insert the vacuum breaker body with seal (H) and nut (H2)

through the basin hole from below, see fig. [2].

2. Slide on seal (H1) with ring (J) and screw on nut (K).

The distance from the top of the body to the bottom of the ring

must be 2 3/16", see fig. [3].

3. Secure vacuum breaker body to the basin by tightening

nut (H2), see fig. [2].

4. Slide on tube (L) and cover (M), see fig. [4].

5. Tighten the connection tee (N) to the vacuum breaker body with

connection nut (O).

Diverter

1. Insert diverter body with nut (P) and seals (Q), (R1 or R2) and

the lift rod assembly through the basin hole from below,

see fig. [5].

2. Slide on seal (R3 or R4) and screw on nut (S) until it is at the

same height as the top of the diverter body (S1).

3. Secure diverter body to the basin by tightening nut (P) using

an 36mm open-ended spanner.

4. Slide on escutcheon (T), see fig. [6].

5. Mount the diverter knob (U) to lift rod assembly (U1).

Verticle spray

1. Insert body with seals (V) from below, see fig. [7].

2. Slide on seals (V1) and secure with nut (W) using an

22mm open-ended spanner.

3. Jet-height can be decreased by turning the nozzle (X) to the left,

turning to the right increases jet-height.

4. Screw on spray face plate (W1).

Fit pop-up drain (28 957), see fold-out page I, ensure that flange

of pop-up drain is sealed.

Connect wideset bidet, see figs. [8] and [9].

1. For this purpose the supply pipes must be installed on to the

angle stops (or other supply points).

2. The cold water supply should be connected on the right, the hot

water supply on the left side.

3. Connect both side valves to the connection tee via the two short

flexible hoses.

4. Connect the vacuum breaker with the blue-marked hose to the

top of the tee and the unmarked hose to the diverter ellbow.

5. Connect the diverter to the verticle spray via the long flexible

hose.

Open cold and hot water-supply and check connections for

watertightness!

Maintenance

Inspect and clean all parts, replace as necessary and grease with

special grease.

Shut off cold and hot water supply.

I. Headpart, see fold-out page II, fig. [10].

1. Remove handle (45 603) or lever (45 609).

2. Unscrew screw (G) and pull off snap insert (F).

3. Unscrew headpart (A) using a 17mm socket wrench.

4. Change complete headpart (A).

II. Vacuum breaker, see fig. [11].

1. Pull off cover (M) and tube (L).

2. Remove circlip (Y), pull out and replace double-ball vacuum

breaker (Z).

3. Loosen nut using an 21mm open-ended spanner and replace

check valve (08 565), see fold-out page I.

III.Vertical spray, see fig. [12].

Unscrew and clean spray face plate (W1) and nozzle (X).

Assemble in reverse order.

Replacement parts, see fold-out page I ( * = special accessories).

Care

Instructions for care of this faucet will be found in the Limited

Warranty supplement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 24016 Atrio Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info