Bedienungsanleitung Grohe 24667 Talia (Seite 4 von 10) (Englisch, Französisch, Spanisch)

759834

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

English

Application

Operation is possible in conjunction with:

• Pressurized storage heaters

• Thermally controlled instantaneous heaters

• Hydraulically controlled instantaneous heaters

Operation with low-pressure storage heaters (displacement water

heaters) is not possible.

Specifications

• Max. flow 13.7 L/min or 3.6 gpm / 45psi

• Flow pressure

- min. 7.25 psi

- recommended 14.5 - 72.5 psi

- greater than 72.5 psi, fit pressure reducing valve

• Max. operating pressure 145 psi

• Test pressure 232 psi

• Temperature

- max. (hot water inlet) 176 °F

• Water connection cold - Right hand

• hot - Left hand

Notes:

- Installation of backflow protection must comply with local codes

and regulations.

- Major pressure differences between cold and hot water supply

should be avoided.

Installation

Refer to the dimensional drawing on fold-out page I.

Flush piping system prior and after installation of faucet

thoroughly!

Side valves

• Valve with a groove on the top edge of the cartridge (A1) and in

addition marked with blue tape should be mounted on the right

(cold water) side, see fold-out page II, fig. [1].

• Valve without a groove on the top edge of the cartridge (A1) and

in addition marked with red tape should be mounted on the left

(hot water) side.

1. Screw the mounting set (B) to the bottom of the thread of the side

valve (A). Make sure that the rubber washer (B1) is on the top of

the fiber washer (B2).

2. Insert the side valve (A) through the basin hole from below.

3. Slide on seals (C) and screw on nut (D). Make sure that the fiber

washer (C1) is on the top of the rubber washer (C2).

4. With 32mm open-ended spanner fasten the side valve (A). The

distance between the top of the headpart and the basin must

be 1 25/32", see fig. [2].

5. Screw the escutcheon (D1) down to the nut (D), see fig. [1].

Mount lever (18 077) not included in the scope of delivery, see

fig. [3].

- Push ring (A2) onto headpart (A1).

- Push on lever.

Install lever (18 085) not included in the scope of delivery.

- Push on lever complete and screw cap (F) onto

headpart (A1).

Vacuum breaker

1. Insert the vacuum breaker body with seal (G) and nut (G1)

through the basin hole from below, see fig. [4].

2. Slide on seal (G2) with ring (H) and screw on nut (I).The distance

from the top of the body to the bottom of the ring must be 2 3/16",

see fig. [6].

3. Secure vacuum breaker body to the basin by tightening

nut (G1), see fig. [4].

4. Slide on tube (J) and cover (K), see fig. [5].

5. Tighten the connection tee (L) to the vacuum breaker body with

connection nut (M).

Diverter

1. Insert diverter body with nut (N) and seals (O), (O1 or O2)

through the basin hole from below, see fig. [7].

2. Slide on seal (O3 or O4) and screw on nut (P) until it is at the

same height as the top of the diverter body (P1).

3. Secure diverter body to the basin by tightening nut (N) using

a 36mm open-ended spanner.

4. Screw on escutcheon (Q), see fold-out page III, fig. [8].

5. Press on snap insert (R) and secure with screw (R1).

6. Push on handle (S).

Verticle spray, see fig. [9].

1. Insert body with seals (T) from below.

2. Slide on seals (T1) and secure with nut (U) using a 22mm open-

ended spanner.

3. Jet-height can be decreased by turning the nozzle (V) to the left,

turning to the right increases jet-height.

4. Screw on spray face plate (W).

Fit pop-up drain (28 957), see fold-out page I, ensure that flange

of pop-up drain is sealed.

Connect wideset bidet, see figs. [10] and [11].

1. For this purpose the supply pipes must be installed on to the

angle stops (or other supply points).

2. The cold water supply should be connected on the right, the hot

water supply on the left side.

3. Connect both side valves to the connection tee via the flexible

hoses.

4. Connect the flexible hose from the vacuum breaker to the

diverter.

5. Connect the verticle spray to the bottom of the diverter.

Open cold and hot water supply and check connections for

leakage!

Maintenance

Inspect and clean all parts, replace as necessary and grease with

special grease (Prod. no. 18 012).

Shut off cold and hot water supply!

I. Replacing the headpart, see fig. [12].

1. Remove lever

Lever (18 077):

- Pull off lever.

- Pull off ring (A2).

Lever (18 085):

- Unscrew cap (F) and pull off lever complete.

2. Unscrew headpart (A1) using a 17mm socket wrench.

3. Change complete ceramic cartridge (A1) or O-ring (A3).

Observe the different replacement part numbers of the

headparts, see fold-out page I.

Observe the correct installation position!

II.Vacuum breaker, see fig. [13].

1. Pull off cover (K) and tube (J).

2. Remove circlip (X), pull out and replace double-ball vacuum

breaker (Z).

3. Loosen nut using a 21mm open-ended spanner and replace

check valve (08 565), see fold-out page I.

III.Vertical spray, see fig. [14].

Unscrew and clean spray face plate (W) and nozzle (V).

Assemble in reverse order.

Replacement parts, see fold-out page I ( * = special accessories).

Care

Instructions for care of this faucet will be found in the Limited

Warranty supplement.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 24667 Talia Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info