Bedienungsanleitung Grohe 31117 Concetto (Seite 5 von 6) (Deutsch)

759337

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

AUS

Application

• for kitchen

Can be used in conjunction with:

• Pressurised storage heaters

• Thermally controlled instantaneous heaters

• Hydraulically controlled instantaneous heaters

Operation with unpressurised storage heaters (= open water

heaters) is not possible.

Technical data

• Flow pressure

- min. 0.5 bar

- recommended 1 - 5 bar

• Operating pressure max. 10 bar

• Test pressure 16 bar

If static pressure is greater than 5 bar, fit pressure reducer.

Avoid major pressure differences between cold and hot water

supply.

• Temperature:

- hot water inlet (max.) 80 °C

- recommended (energy saving) 60 °C

• Water connection: cold - right

hot - left

• Clamping length max. 60mm

Note:

All GROHE single-hole mixers with pull-out sprays are

equipped with non-return valves.

Installation

Flush piping system prior and after installation of fitting

thoroughly (Consider EN 806)!

This product must be installed in conformance with local codes

e.g. AS/NZS 3500 series of standard!

Connect sink mixer,

see fold-out page II, Figs. [1] and [3].

Refer to the dimensional drawing on fold-out page I.

The cold-water supply must be connected on the right and the

hot-water supply on the left.

Note:

If the support plate (A) is omitted, the clamping length can be

increased by 15mm.

Connect the spray hose (B), see Figs. [2] and [4].

1. Feed the spray hose (B) through the spout, see Fig. [2].

2. Feed the spray hose (B) through the mixer body from above

and fit spout (C) so that it snaps into place.

3. Push spring (D) onto spray hose (B) from below,

see Figs. [2] and [4].

4. Screw snap coupling (E) with non-return valve (F) on the

end of the spray hose (B) and tighten by hand.

5. Pull the sleeve (E1) of the snap coupling (E) downwards and

fit to the union (G).

Open cold and hot water supply and check connections

for leakage!

Check fitting for correct operation, see Figs. [5].

Flow rate limiter

This mixer is fitted with a flow rate limiter, permitting an

infinitely variable individual reduction of the flow rate.

The highest possible flow rate is set by the factory before

despatch.

The use of flow rate limiters in combination with hydraulic

instantaneous water heaters is not recommended.

To activate see "Replacing the cartridge" point 1 to 3,

Figs. [6] and [7].

Maintenance

Inspect and clean all parts, replace as necessary and grease

with special grease.

Shut off cold and hot water supply!

I. Replacing the cartridge, see fold-out pageII, Fig. [6].

1. Lever out plug (H).

2. Remove set screw (J) using a 3mm socket spanner and pull

off lever (K).

3. Pull off cap (L).

4. Screw out screwing (M) with key 30mm.

5. Change complete cartridge (N).

Assemble in reverse order.

Observe the correct installation position!

Make sure that the cartridge seals engage in the grooves on

the housing.

Screw in and tighten screwing (M).

II. Non-return valve, see fold-out page II, Fig. [8].

1. Unscrew non-return valve body (O).

2. Unmount non-return valve (O1).

Assemble in reverse order.

Replacement parts, see fold-out page I ( * = special

accessories).

Care

For directions on the care of this mixer, please refer to the

accompanying Care Instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 31117 Concetto Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info