Bedienungsanleitung Grohe 31326 Blue (Seite 25 von 120) (Alle Sprachen)

759335

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

Use only original spare parts and accessories. The use of other

parts will result in voiding the warranty and the CE marking, and

could cause injury.

The filter head must be replaced after 5 years.

Technical data cooler/carbonator electrical data:

• Connection: Wall socket with earth wire,

protected via a 10 A fuse

• Voltage supply: 230 V AC / 50 Hz

• Max. power consumption: 240 W

• Type of protection: IP 21

• Relative air humidity: max. 80%

• Refrigerant: 0.040 kg - R600a

• Safety shut-off of pump: approx. 4:30 min

• Operating pressure: min. 0,2 MPa - max. 1 MPa

•Max. CO

2 inlet pressure: 0.48 MPa

• Max. refrigerant pressure: 3.0 MPa

• WLAN: 2,4 GHz, IEEE 802.11 b/g/n/e/i

• Bluetooth: v4.2 BLE

Sanitary data:

• Cooler/carbonator cooled water capacity: 1.4 l

• Operating pressure: max. 0.6 MPa

• Flow rate at 0.3 MPa flow pressure: approx. 2 l/min

• Ambient temperature: 4 – 32 °C

• Temperature

– Cooler/carbonator water inlet: max. 20 °C

– Cooled water temperature: approx. 5 – 10 °C

• Sound pressure level LpA (frestanding): 50 ± 4 dB

• Adjustable bypass, factory setting: 2

• Filter capacity Bypass Position 2

(Carbonate hardness 17 - 24 °KH): max. 600 litres

corresponds to max. 12 months

• Water connection

– Cooler/carbonator: cold - blue

Electrical test data:

• Software class: A

• Contamination class: 2

• Rated surge voltage: 2,500 V

The test for electromagnetic compatibility (interference emission

test) was performed at the rated voltage and rated current.

Technical data fitting:

• Flow pressure: 0.2 – 0.9 MPa

• Operating pressure: max. 1 MPa

• Test pressure: 1.6 MPa

To comply with noise levels if static pressure exceeds 5 bar, a

pressure reducing valve must be fitted.

Avoid major pressure differences between hot and cold water

supply.

• Flow rate at 3 bar flow pressure: approx. 7 l/min

• Temperature

– Hot water inlet: max. 70 °C

– Recommended (energy saving): 60 °C

Water connection: cold - right

hot - left

Thermical disinfektion of the fitting is possible.

GROHE ONDUS app and connection to the internet

A GROHE Blue cooler connected to the internet via Wi-Fi can be

integrated and configured in the GROHE ONDUS app. This app

can be used to deliver messages in the form of push notifications.

A WLAN router with internet access

(2.4 GHz, IEEE 802.11b/g/n) is required.

Only WLAN channels 1 – 11 can be used.

Installation of the app:

If the app or the device firmware requires updating, the smartphone

must be located in the immediate vicinity of the GROHE Blue

cooler. In this way, possible interruptions in function can be

controlled and rectified.

Operating conditions

Interference sources

The transmitter/receiver unit operates in the ISM frequency band

(2.4 GHz). Installation in proximity to devices with the same

frequency band (e.g. WLAN devices, HF components, etc.

[observe manufacturer documentation!]) should be avoided.

Obstructions/barriers

Wireless reception can be impaired and interrupted under

unfavourable surrounding conditions, in buildings/rooms with

reinforced concrete walls, steel and iron frames or in proximity to

obstacles (e.g. furniture) made of metal. Where necessary, a

WLAN repeater must be connected to the main router in order to

increase the range of the radio signal.

Installation and commissioning

GROHE recommends a depth of min. 510 mm for

the cabinet.

Flush pipes thoroughly before and after installation

(observe EN 806)!

Adjust bypass of filterhead according to local carbonate

hardness and connect filter cartridge.

The carbonate hardness can be tested by using the enclosed test

strip or the relevant water supplier can provide information on the

carbonate hardness.

The fitting has a system-related run-on time of approx. 1 s.

Note: Make sure that the water inlet hose does not come loose

by movement when installing the cooler.

When transporting or installing the cooler/carbonator,

cooling fluid may have run into the lines.

In order to ensure that the cooling fluid has run back, the

cooler/carbonator may only be installed following a pause

of 24 hours.

Display:

In the inactive state, the remaining filter capacity is displayed in per

cent.

When carbonate hardness ≤9° the use of activated carbon

filter (Order no.: 40 547 001) is recommended.

The cooler/carbonator of the GROHE Blue® fitting is set for

operation with the S size filter cartridge (Prod no.: 40 404 001) at

the factory.

For operation with other filter cartridges the cooler/carbonator must

be set out.

Apple: Android:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Grohe 31326 Blue Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info